EnPak® A60 Work Truck Solution - MillerWelds

EnPak® A60HGE, Open Center

907598
A revolutionary, fully-integrated power system for work trucks. EnPak combines a rotary-screw air compressor, hydraulic pump, generator and a 24.8 HP, Tier IV Final diesel engine in a single unit and is fully-functional with the truck turned off.
Compare

Open Center
907598

Closed Center
907599

Air
907598001

Air Maxstar
951683

Air Multimatic
951680

Closed Center Maxstar
951682

Closed Center Multimatic
951653

Open Center Maxstar
951681

Open Center Multimatic
951652

Spec Sheet (ENG)

Features

30% Less Fuel
Exclusive EnPak design reduces fuel use for significant cost savings while delivering the performance that users demand resulting in maximum productivity. Load-Management System monitors accessory requirements and precisely adjusts the engine's speed to match demand, delivering only the amount of power required and minimizing fuel used. Auto Start/Stop Technology shuts off the engine when no accessory loads are detected, increasing fuel savings as well as reducing job site noise and exhaust emissions. When a load is applied, the engine automatically starts up quickly. EnVerter™ Technology delivers up to 2,400 watts of continious 120 V, 60 Hz, pure sine wave power at low engine speeds, providing power for many tools and lights while reducing fuel consumption and decresing job site noise.
Extend Work Truck Life
Turning off a work truck and turning on EnPak can make a work truck last longer. Using EnPak for jobsite functions instead of work the truck's PTO can reduce the truck's engine idle time by up to 50%, extending the life of its drive train.
20 gpm hydraulic pump
The Eaton variable-displacement piston hydraulic pump seemlessly integrated fuel-saving strategies with precise, high-performance operation. The result is lower fuel costs, and well-regulated hydraulic fluid flow for smooth, reliable, and precise crane operation.  The low-speed lock option further enhances control, minimizing hydraulic flow for maximum precision in crane operation.
Spend Less On Maintenance
Work truck maintenance can't be ignored—but its frequency can be reduced. Turning off a work truck and turning on EnPak can save owners money in several ways. EnPak: Has lower preventative maintenance costs Does not require diesel exhaust fluid Has no diesel particulate filter to clean or replace
60 cfm air compressor
EnPak's rotary-screw air compressor can drive a wide variety of tools; it's high air flow capacity can easily power 1-inch impact wrenches and pneumatic pumps—all while minimizing fuel use.
Powerful, Portable Welder Solutions
As the world's leading manufacturer of arc welding and cutting equipment, Miller produces a full line of high-quality, multi-process welders capable of MIG, TIG, and Stick operations as well as arc gouging. EnPak can power several of these superior performing welders with its 6,000 watt generator.The Miller® Maxstar® 210 STR and the Miller Multimatic™ 200 welders provide EnPak users with superior arc characteristics for strong, quality welds. These powerful, portable welding solutions come in packages that weigh less than 35 pounds—so operators can benefit from a work truck that can carry more, weigh less and is equipped with easier to handle, easier to move equipment.See Maxstar 200 STR or Multimatic 200 for detailed specifications.
6,000-watt generator
EnPak's low maintenance generator minimizes down time with a direct-drive, brushless design, which eliminates the need to replace belts and brushes, while producing up to 6,000 watts of continious 120/240 V, 60 Hz power for high demand applications including welders.
More Capabilities, Less Noise
On a busy jobsite, noise reduction can improve the overall working environment and even make the jobsite a safer place to be. EnPak's specially designed encloser reduces sound output 10dB compared to a PTO system that is running all the time, regardless of the tools in use. With auto start/stop technology, EnPak only produces sound when it's in operation.

Specifications

Product Literature

EnPak A60 Brochure

General Specifications

Title EnPak® A60HGE, Open Center
Industries Interests Construction
Infrastructure
Maintenance and Repair - Field Operations
Mechanical Contracting
Work / Service Trucks
Cold Weather Starting Aids Glow Plugs
Block Heater
Engine Brand Kubota
Engine Compliance T4F
Engine Idle Speed 1800 RPM
Engine Weld Speed 1800 RPM
2600 RPM
3200 RPM
3600 RPM
Fuel Type Diesel
Horsepower 24.8 hp
Single Phase Generator Continuous Power 6000 W
Net Width 21 in
Net Height 30 in
Net Length 47 in
Net Weight 832 lbs
Warranty 3 Years
Engine Warranties
Miller's True Blue Warranty

Resources

Literature

EnPak Warranty

Truck Installation Diagram 265796 (PDF)

EnPak Bucket Truck Flyer

EnPak Sales Territories Map

EnPak A60 Brochure

EnPak Welding Packages Flyer

EnPak A60 Flyer

Articles

A worker with an EnPak work truck solution on the jobsite
Regular Maintenance Optimizes Performance of Work Truck Solutions
Maintenance is critical to keeping an EnPak work truck solution running optimally - to optimize performance and reduce unplanned downtime.
Potential Savings, Payback Worth Investment of EnPak®
A mechanic's truck is a substantial and important investment to anyone whose job it is to guarantee the uptime of heavy equipment in the construction industry. Here are a few factors to look at when deciding to go with a traditional PTO set-up versus Miller Electric Mfg. Co.'s new EnPak Mechanic Series diesel-driven air compressor, hydraulic pump and generator.
Equipment Dealer Service Department Reduces Mechanic's Truck Engine Hours, Idle Time & Fuel Use
EnPak's 40 CFM air compressor provides continuous air, even when running a one-inch impact wrench, compared to PTO-driven air compressors that require field technicians to wait for air to build up. Field service technicians are trained from Day 1 to leave their truck's engine running in order to power the PTO, thereby powering all hydraulic and pneumatic tools needed in field repair. This adds more engine hours and wear to a truck's drive train than is necessary. A new, truck-integrated power source—EnPak® Mechanic Series designed and manufactured by Miller Electric Mfg. Co.—has proven to reduce engine hours, idle times and fuel use, and figures to substantially extend the life of a mechanic's truck at Brandeis.

Videos

Turn off your truck. Turn on your Enpak and reduce downtime and costs
When your truck is down, you’re down. EnPak by Miller is an integrated power system that allows you to work with the truck...
Company Decreases Fuel and Operation Costs with EnPak Power System for Work Trucks
To meet the wide variety of its customer needs, while also lowering fuel and operation costs, Butler Machinery decided to...
EnPak: fully integrated power system for work trucks with air, auxiliary power, hydraulic capability
EnPak is a fully integrated power system for work trucks -- including bucket trucks -- with air, auxiliary power and...

Related Items

EnPak A28GBW
EnPak® A28GBW 15' Remote Panel Leads $9,629.00

The EnPak® A28GBW is the industry-leading work truck power solution that gives your truck and crew more capabilities, while reducing expenses and boosting profitability. Ruggedly built and rigorously tested, the EnPak A28 delivers the reliability and performance you expect from Miller.

EnPak A28GBW
EnPak® A28GBW 30' Remote Panel Leads $9,895.00

The EnPak® A28GBW is the industry-leading work truck power solution that gives your truck and crew more capabilities, while reducing expenses and boosting profitability. Ruggedly built and rigorously tested, the EnPak A28 delivers the reliability and performance you expect from Miller.

Multimatic 200 Package
Multimatic (R) 200 Multiprocess Welder $1,999.00

Lightweight MIG, Stick and TIG welder. Impact-resistant case provides durability on the job. This all-in-one multiprocess welder connects to 120 or 230 volt input power. Welds up to 3/8” mild steel.
Trailblazer 302 Air Pak
Trailblazer® 302 Air Pak™ w/GFCI, elec fuel pump $12,475.00

Powerful all-in-one tool is designed for repair and construction with unbeatable multiprocess weld quality, integrated rotary screw air compressor, and 13,000 watts of generator power for job site tools.