Project Submitted: 12/19/2012
The intent of this design was originally to help improve fuel mileage by utilizing a â€œwedgeâ€ type bed cover to eliminate/reduce laminar airflow separation that is normally associated with traditional tonneau bed covers and bed caps.
Originally, it was just going to be a non-removable â€œwedgeâ€ but after thinking about it, it did not take much to make it much more functional (removable)for a variety of uses.
The main frame, semi-removable (bolted to the truck bed), consists of 3"x3" steel angle that runs the length of the bed on both sides and across the front of the bed. These angles have four tie downs attached on both sides for fastening loads in the bed. If required for load retention, tie-downs will also work under the steel angle anywhere along the length of the bed. There is a front â€œhoopâ€ fabricated from 2" x 6" rectangular steel, roughly conforming to the cab profile. The hoop uprights also have tie-downs attached in order to facilitate fastening down loads when the cap is removed. The top cross bar of the front â€œhoopâ€ also extends beyond the uprights, roughly to the width of the truck bed, and has 6â€x6â€ steel plates welded onto both ends, which have two Â½â€ holes to accept ratchet straps for the retention of long loads with the â€œwedgeâ€ removed. Again, the rails and front hoop assembly is bolted to the bed and remain in place when the cap is removed.
The â€œwedgeâ€ frame is fabricated from 1" square steel (aluminum could be used to save weight) and is covered with .040" black anodized aluminum. The â€œwedgeâ€ is hinged at the top horizontal bar of the hoop and raised/supported with gas lift struts.
If you notice in the pictures with the white skid/load in the bed of the truck, I have also made two adjustable struts for the back/rear of the â€œwedgeâ€ in order to adjust the height of the cap when carrying taller loads. The cap is normally in the full closed position but these adjustable struts allow secure closure at various raised and locked positions (up to slightly above horizontal).
When closed and locked/pinned in the full closed position the â€œwedgeâ€ cannot be opened IF the truck has a locking tailgate (either factory or aftermarket). There is no need for lock-type hardware on the â€œwedgeâ€ itself.
The â€œwedgeâ€ itself weighs approx. 100#. The â€œwedgeâ€ is removed from the frame by taking out the hinge pins that attach it to the top of the front hoop and disengaging the gas lift struts. This takes less than 5 minutes and only requires two people.
Briefly this â€œwedgeâ€ can be used and has the benefits of a tonneau/bed cover with additional height, can be used in a like a conventional cap (but not weather tight) in a raised position or completely removed for oversize/long loads.
It is not weather tight as I have constructed it right now but would be weather tight with the addition of a front window and weather-strip around the â€œwedgeâ€ perimeter.
To satisfy D.O.T. requirements for a third/high mounted brake light I installed two brake light/turn signals in the trailing edge of the â€œwedgeâ€ that operate from the trailer light connector and can be unplugged when the â€œwedgeâ€ is not on the truck.
Main frame (bed mounted) fabricated from 2"x6" rectangular steel and 3"x3" angle steel.
"Wedge" fabricated from 1" square steel tube and .040" aluminum sheet.
Millermatic 252, Spectrum 625 X-TREME Plasme.
2'x6" steel tube, 1" swuare steel tube,3"x3" steel angle, .040" aluminum sheet, 2 steel hinges, 4 Dodge Caravan lift gate struts, 2 marker lights, 8 carriage bolts and nuts, wire, trailer light connector
| Auto Cycle
To activate your FREE subscription today, simply select which newsletter(s) you would like to receive and complete the form below.
Already signed up? Manage your subscription(s) by signing into your account. Or if you don't have a Miller account, create one today. Sign in / Create Account.
*Please select at least one e-Newsletter.
You can manage your subscription(s) by signing into your account. Or if you don't have a Miller account, create one today. Sign in / Create Account.