Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Page 1 of 2 12 LastLast
Results 1 to 10 of 70

Hybrid View

  1. #1
    Join Date
    Sep 2005
    Location
    S.W. Pennsylvania
    Posts
    2,250

    Default 6 speed tranny's for Harley's

    I'm putting new gears in my 4 speed ( 1984 Soft tail ) and a lot of people ask why I don't spend a little more and get a 6 speed tranny. I don't get this 6 speed stuff, I don't use the 4 gears I have most of the time. This whole idea of adding more gears to a bigger inch motor just seems backwards to me. More gears is usually to help an under powered engine. Having 100 plus inches and adding 2 more gears seems like a lot of extra weight and shifting with no real gain. What I'm doing is putting a lower first ( 2.60 in place of a 2.44 ) and upping my high end with a larger transmission sprocket and a smaller wheel sprocket. ( 24 and 49 tooth) This puts 1st very close to stock and a 4th cruising speed calculated at about 74 mph at 3100 rpm. Thats about 300 rpm less than stock.
    I just have an 80 inch engine and I think this gearing will serve me well on the street but I think if I were to drag race a 100 inch or bigger I would be tempted to go with a 3 speed. Any way, I was just wondering if any one here is racing the big inchers and what they are using transmission wise ? Also any comments from any one using a 6 speed ?

    If any one is interested, here are my new ratio's.
    primary - 1.54 / 1
    1st - 2.60 / 1
    2nd - 1.82 / 1
    3rd - 1.23 / 1
    4th - 1 / 1
    final - 24 - 49 front & rear tooth count


    Here are my old ratio's.
    primary - 1.54 / 1
    1st - 2.44 / 1
    2nd - 1.65 / 1
    3rd - 1.23 / 1
    4th - 1 / 1
    final - 23 - 48 front & rear tooth count ( stock had a 51 tooth rear )

    With my health the way it is, I was considering trying to find a tranny with a reverse in it. Then decided, naa. I want to keep first slowed down for when I get out in the National forests and such.
    To all who contribute to this board.
    My sincere thanks , Pete.

    Pureox OA
    Westinghouse 300 amp AC stick
    Miller Syncrowave 250
    Hexacon 250 watt solder iron

  2. #2
    Join Date
    Aug 2006
    Location
    near rochester NY
    Posts
    9,881

    Default

    if you are not planing on racing it there realy dosent seem any point to the 6 gears. like ya said you have no need to stay in the power band just crose it.
    a reverse might not be too bad an idea, i dont know what they run $$ wise but on a big bike it could come in handy. i know they make them just dont know how much $$ it would be or if its werth the $$ to ya.
    man i gotta get another bike.
    thanks for the help
    ......or..........
    hope i helped

    feel free to shoot me an e-mail direct i have time to chat. james@newyorkmetalart.com
    summer is here, plant a tree. if you don't have space or time to plant one sponsor some one else to plant one for you. a tree is an investment in our planet, help it out.
    JAMES

  3. #3
    Join Date
    Oct 2004
    Location
    Edmonton, Alberta
    Posts
    7,742

    Default

    On the lower displacement engines like your puny harley, true there isn't much point getting the 6spd, though on my IronHorse texas chopper running a 124 CI with alotta extra torque and zoom power it's nice to have the extra gears.....

  4. #4
    Join Date
    Jul 2006
    Location
    Sarnia,Ontario,Canada
    Posts
    28

    Default

    Quote Originally Posted by cruizer View Post
    On the lower displacement engines like your puny harley, true there isn't much point getting the 6spd, though on my IronHorse texas chopper running a 124 CI with alotta extra torque and zoom power it's nice to have the extra gears.....

    And youll need them to catch the Honda's

  5. #5
    Join Date
    Aug 2006
    Location
    near rochester NY
    Posts
    9,881

    Default

    And youll need them to catch the Honda's

    ummm.... .......... dont you mean to TRY to catch the honda's.
    thanks for the help
    ......or..........
    hope i helped

    feel free to shoot me an e-mail direct i have time to chat. james@newyorkmetalart.com
    summer is here, plant a tree. if you don't have space or time to plant one sponsor some one else to plant one for you. a tree is an investment in our planet, help it out.
    JAMES

  6. #6
    Join Date
    Sep 2005
    Location
    S.W. Pennsylvania
    Posts
    2,250

    Default

    Quote Originally Posted by cruizer View Post
    On the lower displacement engines like your puny harley, true there isn't much point getting the 6spd, though on my IronHorse texas chopper running a 124 CI with alotta extra torque and zoom power it's nice to have the extra gears.....
    I think you missed my point. On my 80 CI, I have enough extra power to spare that if I'm in 1st gear I'll skip second and go directly to 3rd, or if I'm in 2nd, I'll skip 3rd and go directly to 4th.
    On you're 124 CI, are you running all 6 gear's consecutively ? Its hard for me to imagine there being much difference between gears since the first five run up to a direct drive the same as my 4 speed, the only difference is the overdrive, I think its like .86 / 1 ratio. Do you know what the 1st gear ratio is on the 6 speed ?
    To all who contribute to this board.
    My sincere thanks , Pete.

    Pureox OA
    Westinghouse 300 amp AC stick
    Miller Syncrowave 250
    Hexacon 250 watt solder iron

  7. #7
    Join Date
    Mar 2005
    Location
    South Eastern Manitoba
    Posts
    29

    Thumbs up

    Keep the 4 and the kicker.

  8. #8
    Join Date
    Aug 2006
    Location
    near rochester NY
    Posts
    9,881

    Default

    your just cruzzzing along like it was ment to be ridden, i agree keep the 4.
    thanks for the help
    ......or..........
    hope i helped

    feel free to shoot me an e-mail direct i have time to chat. james@newyorkmetalart.com
    summer is here, plant a tree. if you don't have space or time to plant one sponsor some one else to plant one for you. a tree is an investment in our planet, help it out.
    JAMES

  9. #9
    Join Date
    Oct 2006
    Posts
    642

    Default

    Quote Originally Posted by cruizer View Post
    On the lower displacement engines like your puny harley, true there isn't much point getting the 6spd, though on my IronHorse texas chopper running a 124 CI with alotta extra torque and zoom power it's nice to have the extra gears.....
    You'll need all the help you can get just to try and keep up with the Suzukis.

    Maybe you could rip a 13 speed tranny out of a Kenworth!

  10. #10
    Join Date
    May 2005
    Posts
    600

    Default

    Quote Originally Posted by harcosparky View Post
    You'll need all the help you can get just to try and keep up with the Suzukis.
    The question is, why do I WANT to keep up with the KawaYamaSuzukda's?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 82

Welding Projects

Special Offers: See the latest Miller deals and promotions.