Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
Miller Welding Discussion Forums - Powered by vBulletin

Results 1 to 8 of 8
  1. #1
    Join Date
    Dec 2013

    Default One machine two torches can it be done?

    New guy going to get flamed for this question. Go ahead lets here it.

    So my question is can you have two torches set up instead of constantly switching out the torches? Let's say by buddy is over tig welding some aluminum so he needs the water cooler torch. In between him welding I'm welding somethat that is steel and don't need the water cooler torch just the air cooler torch. Is it possible for me to start to weld on something with out having to go unhook water cooled torch and hook up air cooled torch? It would save us time. If it won't work or not a good idea let me know. Would use same pedal so no chance of us both trying to use the machine at the same time.

  2. #2
    Join Date
    Nov 2003


    If I understand your question....

    you want to alternate torch use not use them both simultaniously..
    is that correct...??

    pretty impractical to try both torches at the same time for a number of reasons including totally different settings..

    BUT ... if you want to alternate between torches and money is no object there are switching devices like the VersaTig...

    I just switch torches as needed....

    Attached Images Attached Images
    Last edited by H80N; 03-10-2014 at 08:28 AM.

    The more you know, The better you know, How little you know......

    “The bitterness of poor quality remains long after the sweetness of low price is forgotten”

    Buy the best tools you can afford.. Learn to use them to the best of your ability.. and take care of them...

    My Blue Stuff:
    Dynasty 350DX Tigrunner
    Dynasty 200DX
    Millermatic 350P w/25ft Alumapro & 30A
    Millermatic 200

    TONS of Non-Blue Equip, plus CNC Mill, Lathes & a Plasmacam..

  3. #3
    Join Date
    May 2011
    Bossier Parish La.


    What kind of machine are you using? This might have a bearing on if it is possible or not. Don't know for sure though.

  4. #4
    Join Date
    Nov 2006
    Lake of the Ozarks MO


    Well if you had a dynasty it would be simply unplug and plug while leaving the cooler lines hooked up
    If you only use a power block then both torches would always be live.
    Not the best idea.
    Miller Dynasty 700...OH YEA BABY!!
    Miller Dynasty 280 with AC independent expansion card
    Miller Dynasty 200 DX "Blue Lightning"

    Miller Bobcat 225 NT (what I began my present Biz with!)
    Miller 30-A Spoolgun
    Miller WC-115-A
    Miller Spectrum 300
    Miller 225 Thunderbolt (my first machine bought new 1980)
    Miller Digital Elite Titanium 9400

  5. #5
    Join Date
    Dec 2013


    Yes I want to alternate and not use them simultaneously.... I have an older synrowave 250DX. Another reason is because I seem to mess up the tungsten right away. Money is an object and if it is to much I will just say forget it.

  6. #6
    Join Date
    Dec 2007



    Here is a possible solution which may be cheaper than the Versa-Tig.

    Will require turning a switch and also a valve but you can leave the torches hooked up.

    1 - Use the Miller Polarity /reversing control.
    It has threaded studs for it's connections.

    Figure 2-5 shows how to wire the tig torches.
    The Miller Polarity /reversing control will switch the torch lead between the torches. You can leave the ground connected to the machine.

    2 - Use a 3 way valve for your argon gas connections to switch the argon to the torch in use.

    This will require you to remember which torch is in use and to supply the gas and power but it will work.

    good luck
    Thermal Arc GTSW400, Airco Heliwelder II, Miller Dynasty 350, Hypertherm 1000, oxy-fuel setup, metal cutting bandsaw, air compressor, drill press, etc.:

    Call me the "Clouseau" of welding !

  7. #7
    Join Date
    Mar 2011
    st-eustache qc.canada


    seems to me a few dinse connectors and couple 3 way valves 1 for gas and 1 for cooling might do the job.

  8. #8
    Join Date
    Dec 2010


    never done a dual tig setup but years ago me and a buddy put a splitter on some leads an we both welded stick at the same time with one machine. it would burn hot until both of us started welding then it evened out.we was welding some skids to a deck with lh.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/ on line 73

Welding Projects

Special Offers: See the latest Miller deals and promotions.