Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Results 1 to 4 of 4

Hybrid View

  1. #1
    Join Date
    May 2013
    Posts
    24

    Default Orientation of Tungsten Using Grinding Wheel

    Hi,

    This is the same information that I wrote in a previous thread; but, it may have been too deep in the thread. So, I hope it's okay to post again.

    I haven't had much time to get setup to dive into TIG.


    I recently purchased two new wheels for a spare bench grinder that I have in the garage that will only be used for tungsten grinding. (One is 80 grit, the other 120.)

    I hope the answer to this question isn't too obvious....

    I understand the need to basically grind along the axis of the tungsten. I just can't visualize the best way to do this with the guard assembly on the bench grinder.

    It's my understanding that I should use the side of the wheel. Is this correct? How about the orientation.... toward the direction of travel, or away from it?

    For others who use a bench top grinder, do you leave the guards in place?

    Maybe it's something that will become clear once I attempt a couple. Sometimes a little advice goes a long way.

    Thanks

    Jeff

  2. #2
    Join Date
    Sep 2005
    Location
    Houston, TX
    Posts
    874

    Default

    Use the face of a dedicated wheel, with the tip of the tungsten facing the wheel just like you would sharpen a chisel. Harbor Freight makes an inexpensive 3" grinder that is perfect for tungsten.

  3. #3
    Join Date
    Dec 2012
    Location
    Simcoe Ontario
    Posts
    89

    Default Orientation of Tungsten Using Grinding Wheel

    What works the best that I've seen is a belt sander that is turning away from you. And always keep moving the tungsten side to side so you don't wear grooves in the belt / grinding wheel. Also never grind on the side of a bench grinder wheel. It's a good way to wear the sides and eventually the face will fly apart. As for the bench grinder gaurd you can lower it and tilt it so you can get a good angle with the tungsten. And uh use a drill makes nice uniform sides and clamps the tungsten well and keeps your fingers away. Good luck

  4. #4

    Default

    Chucking up your tungsten in a cordless drill & grinding length ways in the center of the wheel is the old tried & true redneck method.
    Miller Trailblazer's ( 2 )...MillerBobcat 250...Millermatic 251's ( 2 )...Miller Syncrowave 200...Miller Syncrowave 180SD...Miller 12VS Suitcases ( 2 )... Hobart Hefty CC/CV Suitcases ( 2 )...Miller 30A Spool Guns ( 2 )...Miller WC 15A Control boxes ( 2 )...Thermo Dynamics Cutmaster 50 Plasma Cutters ( 2 )...Thermo Arc Hi Freq Units ( 2 )...Smith / Victor O/A Sets...DeWalt Power Tools...Craftsman / Snap On Hand Tools... Two Dodge Mobile Rigs

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 62

Welding Projects

Special Offers: See the latest Miller deals and promotions.

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 137