Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Results 1 to 6 of 6
  1. #1

    Default Strength of equipment

    How does this rack stay strong enough to hold up to 500kg loads with all the holes? I would have thought it would weaken a structure.

  2. #2

    Default

    Add Content
    Attached Images Attached Images

  3. #3
    Join Date
    Dec 2011
    Posts
    382

    Default

    I don't think 500kg is that much for that structure depending of course on the guage of the tubing and how far you drop the 500kg load onto it. That said each tube is essentially 4 angles with the extreme edge of their legs re-inforced by the interconnection to to the adjacent angles. If you partially collapse any of the tubes then it is a whole other ball game. Take a look at adjustable pallet racking. It holds 1000s of kgs and is also punched full of slots.---Meltedmetal

  4. #4
    Join Date
    Oct 2009
    Location
    Reno, NV
    Posts
    298

    Default

    The vast majority of the load is compression, so I'd say that is how it does it. If, for example, one end of the rack was securely attached to the wall, with it cantilevered out (no support bracing) and the weight placed out near the end away from the wall, the weight bearing capacity would be hugely less than when the load is compression as it is in the picture. Kind of like how you can sit on the end of a pretty skinny rod with a seat on the end of it as long as it is pointed straight up, but if you put one end of the same rod in the vise and push down on the other end, you can easily bend it.

    A lot of what can be supported by any structure depends upon the material, but the direction of the forces involved and if the loads are compression, torque, bending, or whatever is also VERY important in how the structure is designed and what sort of loads it can bear.
    Don J
    Reno, NV

    Never pick a fight with an old guy. Old guys are too smart to fight and get hurt. They'll just kill you and get it over with.

  5. #5

    Default Strength of equipment

    Unreal information. Thanks again, I was having doubts about building something similar. But I'll bang it out now.

  6. #6
    Join Date
    Dec 2007
    Location
    PA
    Posts
    346

    Default

    Here is an example we have all seen.and perhaps used ourselves.

    As Don pointed out, the loads are mostly vertical in both cases.

    However all it takes is a bit of side load or a weak side member and the frame could collapse.

    4 empty soda cans will support a person's weight if they are undamaged but if there is a dent in one, look out.
    Attached Images Attached Images
    Thermal Arc GTSW400, Airco Heliwelder II, Miller Dynasty 350, Hypertherm 1000, oxy-fuel setup, metal cutting bandsaw, air compressor, drill press, etc.:

    Call me the "Clouseau" of welding !

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 62

Welding Projects

Special Offers: See the latest Miller deals and promotions.

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 137