Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Results 1 to 9 of 9

Hybrid View

  1. #1
    Join Date
    Feb 2013
    Location
    caddo mills, tx
    Posts
    1

    Default Cruizer- XMT 304 Problem

    i've had this baby for a few days and all i do is dream about it. my pal over in the weldingweb.com said 'cruizer could input

    any help greatly appreciated in finding the values for these little crispy critters! I beleive ive found the black resistor labeled R7 to be 200 ohm 20 watt. Plzzz, any ideas, info or values on the piece the red arrow is pointing at? He's labeled C6 . He got a little melted touching against blown R7
    Attached Images Attached Images

  2. #2
    Join Date
    Oct 2004
    Location
    Edmonton, Alberta
    Posts
    7,465

    Default

    Arrow is pointing at a cap ( blackened but likely still ok), the resistor itself is a 200 ohm 25 watt. Now in order for this to blow, that SR1 it was sitting on is roasted. So it took a major surge. I'd suggest you check the auxillary transformer. The round thing up and at the back of the machine. Also check the output board (right side vertical board) also houses the IGBT's

  3. #3
    Join Date
    May 2009
    Location
    Muskogee Oklahoma
    Posts
    245

    Default

    If it took a big hit, you might want to check R250 on PC1 and make sure it's not toast. It's located toward the front of the board to the right of RC4.

  4. #4
    Join Date
    Oct 2004
    Location
    Edmonton, Alberta
    Posts
    7,465

    Default

    Hay Bella, I've got a dilema with another 304, unit has 52vdc Ocv, Everything tests fine, swapped out pc3 with my test board, pc1 is new, igbt's are new as well as, SR1. Unplugged the hall to no effect, Caps are charging to 288 Vdc (208 line)

    No error code.

  5. #5
    Join Date
    May 2009
    Location
    Muskogee Oklahoma
    Posts
    245

    Default

    Is the 52v OCV showing on both your DVM across the output studs and the readout on the machine?

  6. #6
    Join Date
    May 2009
    Location
    Muskogee Oklahoma
    Posts
    245

    Default

    Caps should be charging closer to 325vdc even with 208vac input but I don't see how that would make up for a loss of almost half of your OCV.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 62

Welding Projects

Special Offers: See the latest Miller deals and promotions.

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 137