Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Page 11 of 17 FirstFirst ... 678910111213141516 ... LastLast
Results 101 to 110 of 168
  1. #101
    Join Date
    Jan 2013
    Location
    NE Illinois
    Posts
    155

    Unhappy

    By the way, for anyone interested, the label on the MM200 says "assembled in the USA".

  2. #102
    Join Date
    Jul 2012
    Location
    Houston,tx
    Posts
    119

    Default Miller Multimatic 200

    Have you usted the tig function homer

  3. #103
    Join Date
    Jan 2013
    Location
    NE Illinois
    Posts
    155

    Default

    I tried it out last night for a few minutes. I didn't really have any scraps that I could use. First time I used lift-arc. Seemed to work pretty well.I got some 1/8 steel today so I'm going to try again this afternoon. I found the Weldcraft AK2 tig accessory kit on Ebay for $25. We'll see what it looks like when it gets here.

  4. #104
    Join Date
    Jul 2012
    Location
    Houston,tx
    Posts
    119

    Default Miller Multimatic 200

    Ok keep me updated according to tracking # multimatic should be here Friday afternoon

  5. #105
    Join Date
    Jan 2013
    Location
    NE Illinois
    Posts
    155

    Default

    Spoolmate 100 arrived this afternoon. Hooked it up, loaded it and tried to run some beads on some scrap 1/4" aluminum I have. Didn't work worth a ****. The Hobart Spoolrunner I had for the HH210 ran great so I was wondering why I couldn't get a good bead going. I checked everything, pre-heated the aluminum, cleaned it, etc., but still no luck. The gun kept sputtering and popping and the wire seemed to melt before it got near the aluminum. Then it dawned on me...with the Multimatic, you have to enter setup and calibrate the spoolgun. I did both the 100ipm & 300ipm tests. After some minor adjustments I got it dialed in. Tried another bead and...much better. Not perfect yet, but part of the problem could be that I had it on auto-set and it only goes up to 3/16" for aluminum. I tweaked the voltage & wire speed and it got a little better. I probably should have turned the auto-set off and just tried to dial it in manually. I'll try that tomorrow or Friday. It did run much better though after calibration and a little adjustment.

  6. #106
    Join Date
    Jul 2012
    Location
    Houston,tx
    Posts
    119

    Default Miller Multimatic 200

    Real nice

  7. #107
    Join Date
    Jul 2012
    Location
    Houston,tx
    Posts
    119

    Default Miller Multimatic 200

    Looks like in getting more ad more anxious by the minute

  8. #108
    Join Date
    Jan 2013
    Location
    NE Illinois
    Posts
    155

    Default

    I know how you feel. It will be worth the wait though...

  9. #109
    Join Date
    Jul 2012
    Location
    Houston,tx
    Posts
    119

    Default Miller Multimatic 200

    If you know anyone selling a miller suitcase 12vs let me know I'm looking for one

  10. #110
    Join Date
    Jan 2013
    Location
    NE Illinois
    Posts
    155

    Default

    That's probably going to be pretty hard to find isn't it?

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 74

Welding Projects

Special Offers: See the latest Miller deals and promotions.