Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Results 1 to 6 of 6
  1. #1

    Default First Post: Some of My Welding (MIG/TIG)

    Hi everyone. My name's Matt, I'm 22 and I run a small business with my friend. We do a lot of exhaust work, as well as any other projects e can get our hands on. We just picked up an extremely lightly used SyncroWave 250DX, so I can finally get back into TIG, my preferred method of making two pieces of hot metal turn into one piece of hot metal. Enjoy! All comments and criticism are welcome!

    For reference, I've been welding for about seven years now.

    Not too pretty here. 2"x.083" DOM steel for a roll cage, obviously TIG. Didn't use enough filler, and the heat was clearly a bit inconsistent.
    197773_1864686738737_3120497_n.jpg

    A bit better here. You can see I stopped being afraid of the filler, though hand control was obviously an issue with this joint.
    199975_1866449662809_5873498_n.jpg

    MIG here. 2.5" OD x 16ga T304. Panel gaps could have been wider, maybe ould have backed off on the wire speed.

    405861_2908565955065_5833791_n.jpg

    395495_2908566995091_2019692286_n.jpg

    404820_2908567315099_2140827274_n.jpg
    Last edited by cobrawannabe; 12-11-2012 at 11:51 AM.

  2. #2

    Default

    MIG on a pulling mower frame, boxing, reinforcement, and seam welding. Mild steel. Was tacked in the middle, should have ground it down and just ran it over.
    424803_4847440425715_680158471_n.jpg

    More:
    27895_4847233580544_704853107_n.jpg

    320648_4846992054506_1971649639_n.jpg

    27895_4847233580544_704853107_n.jpg

    MIG, T304, 3"x16ga.
    486880_418125874913232_2068507959_n.jpg

  3. #3

  4. #4

  5. #5

  6. #6

    Default

    Thanks for the warm welcome!

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 82

Welding Projects

Special Offers: See the latest Miller deals and promotions.