Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Results 1 to 4 of 4

Thread: Stinger

  1. #1
    Join Date
    Oct 2012
    Location
    Deployment
    Posts
    1

    Question Stinger

    Is there any safety concerns of moving a stinger to a different lead? I ask as most of my training in the military isnt as sufficent as I need it. Thank you.

  2. #2

    Default

    Either turn off the welding machine that will be left without a stinger or else tape up the cable end so it cannot arc out

  3. #3
    Join Date
    Sep 2005
    Location
    WY...armpit of U.S.A.
    Posts
    659

    Default

    Sounds like you are asking about swapping out a stinger from one lead to another to replace a damaged lead or extend a shorter lead. If so, no problem. You should be able to access the setscrew on the bottom of the handle, if this is for a stick welder, and loosen it enough to pull off the stinger. Clean the recess hole in the stinger with either some sandpaper or a section of Scotchbrite and shove in the new lead's end with only enough insulation cut off the end to almost fill the recess. Tighten the setscrew back down and you're done...go back and retighten again after some use as there will probably be some extra bit of tightening necessary after the lead is flexed around a bit.
    Miller 251...sold the spoolgun to DiverBill.
    Miller DialArc 250
    Lincoln PrecisionTig 275
    Hypertherm 900 plasma cutter
    Bridgeport "J" head mill...tooled up
    Jet 14 X 40 lathe...ditto
    South Bend 9" lathe...yeah, got the change gears too
    Logan 7" shaper
    Ellis 3000 band saw
    Hossfeld bender w/shopbuilt hyd.
    Victor Journeyman torch and gauges
    3 Gerstner boxes of mostly Starrett tools
    Lots of dust bunnies
    Too small of a shop at 40 X 59.

  4. #4
    Join Date
    Sep 2012
    Location
    London
    Posts
    21

    Default

    Well, I'll recommend the precautions stated by Wyoroy. In addition, do follow the safety precautions while wielding and wear a highly insulated protection clothing. Tapping the bare cable end or completely switching off the wielding machine while removing the stinger bead can further safeguard you.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 82

Welding Projects

Special Offers: See the latest Miller deals and promotions.