im working on a hitch mounted smoker to tailgate with. drafted up a design on Inventor today. ill post some pics when i get any.
Results 61 to 70 of 113
-
10-17-2008, 04:40 PM #61
Member
- Join Date
- Oct 2008
- Location
- Texas
- Posts
- 52
-
10-17-2008, 05:54 PM #62
Member
- Join Date
- Sep 2008
- Location
- Blacksburg Va.
- Posts
- 60
This is a stand that I built to make my bead roller mobile
-
10-21-2008, 11:45 PM #63
Junior Member
- Join Date
- Jan 2007
- Location
- Waterford Ca
- Posts
- 12
Bike
I like to build recumbent bikes[IMG]
[/IMG]
-
10-30-2008, 05:58 AM #64
Junior Member
- Join Date
- Oct 2008
- Location
- Michigan
- Posts
- 1
i tried
Apparently all my pics. are too big.
bummer
-
10-30-2008, 10:35 PM #65
Senior Member
- Join Date
- Jan 2008
- Location
- In wal-mart
- Posts
- 460
Very nice work. I need to weld something up, but I got welders block right now.
-
11-02-2008, 08:33 AM #66
Senior Member
- Join Date
- Feb 2006
- Posts
- 411
If I had a Mail box that big, I think I would get some BIG Bills in it. Ha Ha
..............
Richard
-
11-02-2008, 08:45 AM #67
Senior Member
- Join Date
- Sep 2005
- Location
- Texas
- Posts
- 279
For XP You can resize your pics w/microsoft picture resizer http://www.microsoft.com/windowsxp/d...powertoys.mspx
Originally Posted by alumidrew
or http://www.irfanview.com/
Good luck
L*S
-
11-02-2008, 04:31 PM #68
Member
- Join Date
- Feb 2008
- Posts
- 42
It doesn't get any simpler than this
(8 pcs including casters)
I also just finished a mobile base for my drill press, but I didn't take any pics yet.
t
-
11-02-2008, 05:48 PM #69
Member
- Join Date
- Sep 2008
- Posts
- 64
Cutoff Saw Stand - Evolution 355
Here are some pics of a cutoff saw stand for an Evolution 355. The right hand table wing is held up by a folding support arm and includes a pull-out extension. The unit is mobile to save shop space, pull out handles are used to move it. One foot is adjustable to accommodate irregularities in the shop floor concrete. Attached to the support table wing is a folding ruler that give quick approximate readings for fast cuts. There is a small slide-in chip deflector just to the right of the blade to keep the metal chunks from flying all over. There is a 3/4" plate on the bottom to act as ballast to prevent tipping. I've used this setup for about 2 years, works really great.
MTBob
____________________________
MM 251 w/Spool gun
MM 135
Evolution Cut Off saw
Logan Lathe
Clausing Mill
Walker Turner Drill Press
-
11-02-2008, 06:55 PM #70
Senior Member
- Join Date
- Dec 2006
- Location
- New Jersey
- Posts
- 779
This is a breaching door that I made as well as a battering ram device. The ram in the pic was a prototype and the final version was changed a bit. I made many of these. Dave http://jerseytactical.com/products/P1010822252.JPG http://jerseytactical.com/products/P1010819.JPG http://jerseytactical.com/photo_gallery/P1010127.jpg
Reply With Quote
