Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Results 1 to 10 of 10

Hybrid View

  1. #1
    Join Date
    Nov 2010
    Location
    Columbus, Ohio
    Posts
    2

    Question Millermatic 200 gun cable flex groumet

    Just picked up a Millermatic 200. Where the gun cable plugs into the unit there is a (for lack of the actual name) flexible groumet that shrouds the gun cable. Due to age of the unit this groumet has cracked and seperated to where one can actually see the woven wire that wraps the cable. I've been advised to just tape it real good with electric tape and its good to go. Now for the reason for this post - Is it safe to tape it up or should I replace groumet (whatever its called) or the dreaded replace the entire gun cable. The welder works fine. Serial number - JK634850 and I believe the gun to be GA - 20C. thanx

  2. #2
    Join Date
    Aug 2008
    Location
    Orange, TX
    Posts
    1,191

    Default

    I assume you're referring to what is called the "strain relief" in the G-20C manual http://www.millerwelds.com/om/o1025d_mil.pdf as item #33. If so and you want to replace it rather than tape it up you can get one here http://miller4less.com/advanced_sear...d5ecaf5cda9872 for $11.35.

    However, I suggest buying two as they have a minimum order amount of $20 so you'd wind up paying about the same for one as you would for two anyhow and you could replace both ends. Or figure out if there is any other part(s) you may need/want to add up to at least the minimum order amount.

    If you don't have it, you can download the MM200 manual here:
    http://www.millerwelds.com/om/o1303m_mil.pdf
    Last edited by duaneb55; 11-02-2010 at 11:16 AM.
    MM200 w/spot controller and Spoolmatic 1
    Syncrowave 180 SD
    Bobcat 225G Plus LPG/NG w/14-pin*
    *Homemade Suitcase Wire Feeder
    *HF-251D-1
    *WC-1S & Spoolmatic 1
    PakMaster 100XL
    Marquette "Star Jet" 21-110

  3. #3
    Join Date
    Nov 2010
    Location
    Columbus, Ohio
    Posts
    2

    Default Many thanx for great info

    You nailed it. Will order 2. I was somewhat skeptical about taping.

  4. #4
    Join Date
    Oct 2012
    Posts
    1

    Default I have same problem

    Duane55,
    Will all the information be accurate for my machine as well? S/N JF918470

    I did s/n search and nothing came up. Machine must be to old!
    Last edited by Darmarhad; 10-10-2012 at 12:56 PM.

  5. #5
    Join Date
    Jul 2010
    Location
    Four Flags city
    Posts
    298

    Default

    I'm no Duane(by a long shot) but here are your manuals,

    http://www.millerwelds.com/om/o1303p_mil.pdf

    http://www.millerwelds.com/om/o1025d_mil.pdf

  6. #6
    Join Date
    Oct 2007
    Location
    Cave Creek Az
    Posts
    965

    Default

    I have run those GA-20c gun for a while and finally replaced with a Bernard Q gun and Miller M-25, both are better guns than than the GA-20c. They are both available on ebay for about $100.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 82

Welding Projects

Special Offers: See the latest Miller deals and promotions.