Metal blade for circular saw

[monte55]

I know this has has been discussed before and I did a search but can't find what I want. I'm thinking of either getting a metal circular saw or a metal blade for one of my wood saws. Anyone used a metal blade on the wood saw? If so, how did it work, what brand etc? Again, I'm talking about 71/4 circular saws. The only way I have to cut a sheet of steel effectively is a plasma cutter. I have saws for everything else.............thanks for any info

Nick

[HMW]

The saw blades I have seen are for the "slower" turning "cold" cut saws. I've demo'd the Evolution saw and it cut right through a pice of 3/8" plate very smooth. Havent tried any other brands. But I wonder on thin stuff if a blade could stand the RPM of a reg circular saw. Would be nice to know if anybody has tried a brand. I use a regular 7-1/4" carbide saw blade on aluminum, but dont think it would live on steel. Just my 2 cents worth, I too am interesested to see if anybody has any info.

Some times these topics get posted and I either miss them or forget them

Never hurts to ask again

[croyall]

I have a Milwaukee Metal cutting circular saw. I love it. I have cut thin sheet metal all the way up to 1/2" plate, as well as schedule 80 pipe. This pipe is a but of a pain but it does a great cut. The blades are expensive but last quite a while so long as you don't force the saw. For aluminum I just use a skill saw with a carbide blade.

[fuzzy]

after burning up my first high dollar metal cutting blade on my 12" compound mitre saw, i bought a router control from harbor freight for something ridiculous like $12. it must be a scr b/c it slows the saw speed very nicely and without much loss of power.

it beats the crap out of a $$ cold saw

fuzzy

[KBar]

I know this has has been discussed before and I did a search but can't find what I want. I'm thinking of either getting a metal circular saw or a metal blade for one of my wood saws. Anyone used a metal blade on the wood saw? If so, how did it work, what brand etc? Again, I'm talking about 71/4 circular saws. The only way I have to cut a sheet of steel effectively is a plasma cutter. I have saws for everything else.............thanks for any info

Nick

Monte

I've used the metal cutting blades (7-1/4) that you can pick up at a hardware store in my circular saw about 5 years ago putting up a pole barn. It was metal siding and roofing I was cutting, did a fabulous job, they go through the metal like soft butter so be careful. Just get the regular abrasive blade. They wear about the same on a circular saw as they would in a chop saw. I would not recommend it for anything heavier than sheet metal though.

[84ZMike]

I have used the Morse metal devil on my reg 7 1/4" saw....didn't last very long....but this one http://www.bulletindustries.com/cata...roducts_id/487 has done very well.......
Mike

[HMW]

Monte

I've used the metal cutting blades (7-1/4) that you can pick up at a hardware store in my circular saw about 5 years ago putting up a pole barn. It was metal siding and roofing I was cutting, did a fabulous job, they go through the metal like soft butter so be careful. Just get the regular abrasive blade. They wear about the same on a circular saw as they would in a chop saw. I would not recommend it for anything heavier than sheet metal though.

I think he's looking blades with "teeth". You can buy the abrasive ones everywhere. I also built a couple pole buidlings and found a metal cut off wheel on a 4 1/2" grinder works great. just make a line with a sharpe and cut away. Lasts a long time too. easier to handle than a circular saw and wont scratch up the paint. Just my 2 cents

[HMW]

I have used the Morse metal devil on my reg 7 1/4" saw....didn't last very long....but this one http://www.bulletindustries.com/cata...roducts_id/487 has done very well.......
Mike

I may try one. i think that is what Monte is looking for, not sure

[migman69]

you want to cut metal this best might work with the proper abrashive wheel

[KBar]

I think he's looking blades with "teeth". You can buy the abrasive ones everywhere. I also built a couple pole buidlings and found a metal cut off wheel on a 4 1/2" grinder works great. just make a line with a sharpe and cut away. Lasts a long time too. easier to handle than a circular saw and wont scratch up the paint. Just my 2 cents

Thats ok with a small grinder but in the small tool section, I use mostly air tools and it was too far to drag an air hose, besides, an air hose gets dangerous when you cut it.

As far as metal blades with teeth, personally I would go with a metal cutting saw rather than a wood saw if you are going to use it on a regular basis. They make them for wood and they make them for metal for a reason.