Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Results 1 to 4 of 4

Thread: Need Mig Info

  1. #1
    Join Date
    Nov 2007
    Location
    New Brunswick, Canada
    Posts
    38

    Default Need Mig Info

    I'm in the market for a mig welder. I have so far done most of my research on line and at local welding supply stores. I will be using this welder for mostly hobby work in my garage and i'd like to eventually work my way up to light fabrication or even making my own utility trailer and possibly selling a few if I can get good at it. I have wired my garage with 230 amp service for that reson. I'm seriously looking at the Millermatic 180 for the simple fact that I was told that If I wanted to weld up to 1/4 inch thick,I shouldn't go any smaller than that. Will this do the trick, can any of you give me additional advice before I make the $1000.00 purchase ? Thanks JC

  2. #2
    Join Date
    Sep 2005
    Location
    Salem ,Ohio
    Posts
    3,902

    Cool

    If i was looking for a small 220v unit it would be a MM180...Bob
    Bob Wright, Grandson of Tee Nee Boat Trailer Founder
    Metal Master Fab Salem, Oh 44460
    Birthplace of the Silver & Deming Drill
    1999 MM185 w/185 Spoolgun,1986 Thunderbolt AC/DC
    Spool Gun conversion. How To Do It. Below.
    http://www.millerwelds.com/resources...php?albumid=48

  3. #3
    Join Date
    Sep 2006
    Location
    Abilene, Texas
    Posts
    639

    Default

    Just over a year ago I was in the market for a mig. Not really knowing much about them, I kept looking at the 135 and the 180 at my LWS. After I started reading some welding forums I switched my choice to the MM210. That was probably the best decision I ever made. If you have 220v and want a GOOD welder with a duty cycle you won't likely blow, then get the MM212 which is the newer version of the 210. It comes on it's own cart. Will carry large bottles. Like I mentioned, longer duty cycle. Holds bigger rolls of wire. Will run a spool gun. To me it's a no brainer unless $$$ don't allow the $1400+ price. Go compare the 212 to the 180 and see what you think. I am sooo glad that I took the step up. If you plan on building trailers you will be happy you spent a few extra $$ too. As they say "trust me".
    Jim

  4. #4
    Join Date
    Aug 2007
    Location
    So. Cal
    Posts
    335

    Default I agree with both!

    The 180 is awesome and like above in this category, this is the machine. However, and like mentioned above as well check and know your specs. The 210 will let you move into areas you would otherwise be limited to. Were it me, I'd wait a tad, save the DRM (Dough-Ray-Me) and get something you probably will never out grow.

    Good Luck

    TacMig
    We depend On:
    Miller | Esab | Lincoln | Fronius
    Baileigh | Drake | Eagle | Knuth
    Victor | Harris | Smith | Bessey
    Snap-On | Hilti | Ingersoll Rand
    Burco/Koco | Onan | BobCat
    Tracker | Infratrol | AmeriCast

    We belong to or support:
    American National Standards Institute
    American Welding Society
    The Welding Institute
    Fabricators & Manufacturing Association Int'l.

    Anderson & Co. LLC
    Metal Cr
    afters

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 82

Welding Projects

Special Offers: See the latest Miller deals and promotions.