Results 21 to 30 of 146
03-23-2008, 03:22 PM #21
Miller Dynasty 700...OH YEA BABY!!
MM 350P...PULSE SPRAYIN' MONSTER
Miller Dynasty 280 with AC independent expansion card
Miller Dynasty 200 DX "Blue Lightning"
Miller Bobcat 225 NT (what I began my present Biz with!)
Miller 30-A Spoolgun
Miller Spectrum 300
Miller 225 Thunderbolt (my first machine bought new 1980)
Miller Digital Elite Titanium 9400
03-26-2008, 12:44 AM #22Member
- Join Date
- Jan 2007
That's OK, years ago my cousin did the same thing with an electric grain auger, picked up the end by grabbing hold of the flighting, somewhere in moving it something caught the cord, which pulled the switch box off the post. The box landed on the ground, turned the switch on which started the auger and proceeded to wrap his arm around the flighting.
When his hired man found him the belts had burned off the motor yet there he laid unable to remove his arm from the auger.
Needless to say he needed more than a couple stitches and a long rehab to get back to normal.
Stuff like this couldn't be made to happen if you tried, but it does happen everyday to some unfortunate soul. Be careful out there..............
03-26-2008, 06:19 AM #23
03-26-2008, 09:01 AM #24Member
- Join Date
- Oct 2007
Made a potato cannon out of a 100lb propane tank with a 2"x8 foot barrel.at 175psi it would launch said potato over 1000 yards.well after a few barley pops,me an my bro decide it would make some cool bubbles if fired into the water,so we charge it up and off to the dock we go.we laid it over the end of the dock,straight down and sat on it because it had quite of kick.Well,8 foot barrel and only 5 feet of water and 3 feet of very soft mud.The last thing i saw before i closed my eyes is what looked like a brown mushroom cloud bigger than any bubble i have ever seen.When i opened my eyes there was a 25 foot brown circle of mud with me an bro in the middle.his brand new boat was also tied up to the dock and had an inch of mud all over it not to mention the two of us that only had two white eyes.The wives and friends on shore were laughing so hard that one of them actually peed and the others couldnt even stand up.Wow those were the days.Trailblazer 302
esab handy plasma 550
21cfm honda compressor
f350 superduty 4x4
Lots of bills lol
03-26-2008, 10:00 AM #25
You just about got smoked.......doobie
Last edited by monte55; 03-26-2008 at 06:56 PM.Nick
Miller 252 Mig
Miller Cricket XL
Millermatic 150 Mig
Miller Syncrowave 200 Tig
Jet Lathe and Mill
Jet 7x12 horz/vert band saw
DeWalt Multi Cutter metal saw
Century 50 Amp Plasma Cutter
20 ton electric/hydraulic vertical press
60" X 60" router/plasma table
Vist my site: www.nixstuff.com
and check out some of my ironwork and other stuff
03-26-2008, 12:37 PM #26Member
- Join Date
- Jan 2008
Thanks doobie, that just made my dayMillermatic 180 Auto Set
03-26-2008, 01:12 PM #27
can you make one and try that, so I can watch???I'm not late...
I'm just on Hawaiian Time
03-26-2008, 06:29 PM #28
How many times do you have to be told?
Ever had your friend tell you to put your glasses on?
Mine did and so I did and the next thing i know, Ive got a stainless steel wire from a wire wheel stuck firmly in my cheek- just below my left eye... My friend reaches over , pulls it out and it started to bleed. Amazing, those glasses are, You never really know if there working or not until you take them off or forget to put them on.. I owe my friend one...Will it weld? I loooove electricity!
Miller 251/30A spool
Precix 5x10 CNC Router12"Z
Standard modern lathe
Cheap Chinese mill that does the trick... sort of...
horizontal 7x12 bandsaw
Roland XC540 PRO III
hammer and screwdriver (most used)
pooper scooper (2nd most used...)
03-26-2008, 07:49 PM #29
We had this guy at work. He was brazing a 2" fitting up in the air on a ladder threw a opening in the sheet rock. When he finished the side facing him he decided to reach the other side of the fitting instead of moving the ladder to the other room. Well, he couldnt see where his rose bud was in the position he had to get into to braze the other side. Burned the heck out of his hand when the rose bud slipped into his glove. Ouch. Someone was joking that he would need a skin graft. (it wasnt that bad) We called him "a** hand" for the rest of the week.Dynasty 200 DX
"We conquer by degrees."
03-26-2008, 08:25 PM #30
Another time we wer working at LAX. The foreman asked me to change a valve up in the air. 50' in the air on one of the big lifts. First we shut off the valve, cutt and removed the old rusty galv pipe after the valve. Opened the valve to let the air bleed out. (it was a comressed air line) Well, 1/2 hr later the foreman comes by & wants to know why we were still changing the valve. We told him that we thought the line was still live. Me and the apprentace were all over the place trying to find an isolation valve for the hanger with no luck. So this foreman demanded that I do it on the fly. Well I knew better but wanted to keep my job. Off came the valve years of rust and all at about 500fps. Still have rust in my left arm and hand 20 years later. It was a bloody mess. Next time a foreman tells me to do something stupid Im not going to do it. Job or not.Dynasty 200 DX
"We conquer by degrees."