This is the welding cart I built for my MM211 welder. I wanted more than just the plain cart avalible for it that has no storage. A welder is just the start, then you make 50 trips to get everything you need. I made places to carry the spoolgun in its box, a small tackel box to carry extra tips and parts, an aluminimum box for gloves, wire, pliers, wrench, wire brush, and other stuff. The front has a holder to roll the cables up on and a sleave to hold the gun while working, also a holder for mig pliers. The machine is bolted to the cart and there is a storage bin between the welder and bottles for the mig whip when using the spool gun. The welder is set to one side making a small ledge to give a work area to set tools and wire rolls on while changing spools. There is a capability to hold 3 bottles and they are secured from moving with 2 ratchet straps. There is a lifting ring on top so the whole rig can be lifted into a truck or trailer ready to weld. A few strategic cross bars to attach tie downs to and she is ready to go.
211 Welder cart.jpg
Front with Gun Holder.jpg
Side work space.jpg
Spool gun storage.jpg
Results 1 to 6 of 6
Thread: MM211 custom welding cart
11-08-2009, 12:54 PM #1
MM211 custom welding cart"The only source of knowledge is experience." Albert Einstein
11-08-2009, 03:37 PM #2
Nice job. Switch your spoolgun over to the regular mig gun tip and you can get rid of 1/2 of your tips and the expense of those little tips...BobBob Wright, Grandson of Tee Nee Boat Trailer Founder
Metal Master Fab Salem, Oh 44460
Birthplace of the Silver & Deming Drill
1999 MM185 w/185 Spoolgun,1986 Thunderbolt AC/DC
11-08-2009, 04:04 PM #3Senior Member
- Join Date
- Dec 2007
- southern California
Very nice! I like the 4-gang j-box on the front of the cart too! All you need is a couple hooks to hang your grinders and hood on and you'll have the complete mobile work station!Millermatic350P/Python, MillermaticReach/Q300
PowCon 300SM, MK Cobramatic
ThermalArc 185ACDC, Dynaflux Tig'r, CK-20
Hypertherm PowerMax 380
-F350 CrewCab 4x4
-LoadNGo utility bed
11-08-2009, 04:21 PM #4
Miller 252 Mig
Miller Cricket XL
Millermatic 150 Mig
Miller Syncrowave 200 Tig
Jet Lathe and Mill
Jet 7x12 horz/vert band saw
DeWalt Multi Cutter metal saw
Century 50 Amp Plasma Cutter
20 ton electric/hydraulic vertical press
60" X 60" router/plasma table
Vist my site: www.nixstuff.com
and check out some of my ironwork and other stuff
11-09-2009, 05:12 PM #5
Nice job, my only suggestion would be to raise the gun holder up some.
A little too low for me !
All in All, nice job though !!
Sunrise Outside My Shop In Delhi, Ontario
- Weldcraft WP26FV Tig Torch setup.
- Arcair- K 4000 CAC.
- LN-25 Wire Feeder
- Lincoln Ranger 8- Engine Drive- CC\CV:
- Miller Econo Twin AC/DC High Freq.
- Lincoln Power Mig 180C
- Horizontal Steel Band Saw
- DeWalt Chop Saw .
- DeWalt Compressor - 13cfm, @ 100 psi.
11-10-2009, 05:32 AM #6
at least it holds everything togather.