I want to build a firewood rack and need to know what material dimensions would be acceptable. I don't have a fancy CAD program so I made a "sketch" in PhotoShop- go ahead and have a free chuckle. I hope I have given enough information to fetch an answer? I may choose to make a couple 4' wide units instead. This will probably end up being heavy if it's 7' wide?
I refuse to buy a bolt together POS from Home Depot when I own MM140- even if it's $500 in labor.
Is 1.5" x 1.5" square A513 tubing overkill or inadequate? What wall thickness will suffice? Am I WAY off base in materials selection?
I got a rough idea of materials cost by getting an online quote from metalsdepot.com. Metals Supermarket will likely be my supplier and I haven't a clue about what they'll charge for this type of material- they're website is a bit shy of functional?
A513 Steel Structural Square Tube 1-1/2 X 1-1/2 X 16GA (.065 wall) 48' = $93
A513 Steel Structural Square Tube 1-1/2 X 1-1/2 X 14 GA (.083 wall) 48' = $118
A513 Steel Structural Square Tube 1-1/2 X 1-1/2 X 11 GA (.120 wall) 48' = $136
Results 1 to 10 of 39
11-01-2009, 08:23 AM #1
building a firewood storage rack. questions
Last edited by Johnny; 11-01-2009 at 09:45 AM.MillerMatic 140 Auto-Set
11-01-2009, 09:01 AM #2
I would look for a metal supplier thats close...BobBob Wright, Grandson of Tee Nee Boat Trailer Founder
Metal Master Fab Salem, Oh 44460
Birthplace of the Silver & Deming Drill
1999 MM185 w/185 Spoolgun,1986 Thunderbolt AC/DC
Spool Gun conversion. How To Do It. Below.
11-01-2009, 09:05 AM #3
11-01-2009, 09:54 AM #4Senior Member
- Join Date
- Oct 2007
Is this going outside? if so you may want to put something under the feet so it doesn't sink.
Looks good. If outside are you going to cover it?Tim Beeker,
(my side bussiness)
Miller Synchrowave 350LX with tigrunner
Esab 450i with wire feeder
Thermal Dynamics cutmaster 51 plasma cutter
Miller aircrafter 330 - sold
Marathon 315mm coldsaw
vertical and horizontal band saws
Dewalt cut off saw
Sand blast cabinet
lots of hand grinders
11-01-2009, 10:01 AM #5
It's going outside. I'll probably add material to the legs so it dosen't dig into my concrete patio.
It will be covered with a lightly customized blue tarp. I sew better than I weld.
another top notch sketch... with skids added
Last edited by Johnny; 11-01-2009 at 10:05 AM.MillerMatic 140 Auto-Set
11-01-2009, 10:10 AM #6
11-01-2009, 11:27 AM #7Senior Member
- Join Date
- May 2008
- Belle Plaine Iowa
Youre going to have a lot of weight 7 feet high with only a 14 inch footprint. To keep from having it fall over on the neighbors poodle, Id make it longer and not as tall. If youre dealing with a confined space bolt it to the garage wall.Who do you call when the lawmakers ignore the law?
Miller AC/DC Thunderbolt 225
Miller 180 w/Autoset
Old cutting torch on LPG
11-01-2009, 11:31 AM #8
11-01-2009, 03:26 PM #9
As a point of reference, Metals Depot's prices are ridiculous.
1"x1"x24' 16ga from them is $23. My price for a 20' length in Los Angeles (where things ain't exactly cheap) is only $6.
11-01-2009, 03:36 PM #10Senior Member
- Join Date
- Sep 2007
- Medford MA
seriously -- for any non-trivial amount of material, find a steel service
center/dealer/...er. the price difference is major.
s to your design -- i built one about the same -- except that it was not
as long and i did not put the stretchers along the top. it works well.
you _might_ want to consider putting only 1 such stretcher along the top.
it would make it easier to load/unload the rack.