Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Results 1 to 10 of 28

Hybrid View

  1. #1
    Join Date
    Nov 2008
    Location
    Kansas City Metro
    Posts
    387

    Default A new hitch on an old Ford

    It seems that my trailer is getting heavier and heavier. So I decided that it was time for a real hitch. I used 3/8" bent plate with a 3" hole for the 3"x1/4" square tube to fit thru. I used 1/4" plate to beef up the area where the receiver tube attached to the 3", front and back. There is 3 grade 8 1/2" bolts on each side.



    Sorry folks I forgot to get the camera until it was pretty well put together.








    Well its gona take one more post to get the rest of the pics.

    Miller 211 A.S. and Spoolmate 100
    Stickmate LX 235 AC / 160 DC.
    Clarke 180 EN Just in case
    Spectrum 375 X-Treme.
    O/A Medium Radnor Torch, Large Victor Torch.
    Milwaukee 14" Chop Saw.
    4 x 6 Horizontal Band Saw.
    Rockworth 80 Gallon 2 Stage 16 SCFM @ 175 PSI , 15 SCFM @ 90 PSI.
    Jackson Passive shade #5 for the plasma.
    I almost forgot the Hobart XVP AD Hood.


    Projects and Misc Albums
    http://picasaweb.google.com/keesfriend Feel Free to Have a Look ( Just keep in mind I am an amateur )

  2. #2
    Join Date
    Nov 2008
    Location
    Kansas City Metro
    Posts
    387

    Default

    As you can see I am not very good at making the transition on the corners, but I hope with practice I can catch on.





    I know the tube is sorta long but it made a great place for the jack while I was fitting the hitch to the frame.



    I marked up my cut lines last night and went to work on it this morning. Between the kids, the wife, and the neighbors I got picked up about dark.

    I ran the little 180 maxed out with .035 wire and co2. I was going to use 7018 but I tried a test piece, and after the destructive test it appeared that I was getting good penetration with the mig. So I ran with it.

    Miller 211 A.S. and Spoolmate 100
    Stickmate LX 235 AC / 160 DC.
    Clarke 180 EN Just in case
    Spectrum 375 X-Treme.
    O/A Medium Radnor Torch, Large Victor Torch.
    Milwaukee 14" Chop Saw.
    4 x 6 Horizontal Band Saw.
    Rockworth 80 Gallon 2 Stage 16 SCFM @ 175 PSI , 15 SCFM @ 90 PSI.
    Jackson Passive shade #5 for the plasma.
    I almost forgot the Hobart XVP AD Hood.


    Projects and Misc Albums
    http://picasaweb.google.com/keesfriend Feel Free to Have a Look ( Just keep in mind I am an amateur )

  3. #3
    Join Date
    Oct 2007
    Location
    Cave Creek Az
    Posts
    985

    Default

    Nice work! It looks like a good design that is safe and well thoughout. I would feel comfortable driving behind it.

  4. #4
    Join Date
    Jan 2007
    Location
    Rosetown, SK.
    Posts
    519

    Default

    That looks nice & beefy. good job.
    252 Miller Mig
    180 Synchrowave
    R - 45 Milling Machine
    Kingston 1100 Lathe
    Miller 2050 Plasma Cutter

  5. #5
    Join Date
    Dec 2007
    Location
    southern California
    Posts
    1,783

    Default

    Looks great, nice work.

    I would cut down the tube protruding forward so a spare tire can fit under the bed.

  6. #6
    Join Date
    Nov 2008
    Location
    Kansas City Metro
    Posts
    387

    Default

    Thank you gentlemen I appreciate it. The average joe wouldn't have a clue what goes into most welding projects.

    I agree about the spare tire. I just have to come up with a good secure way to mount it again. When I got the truck it didn't have a spare and the carrier was trashed. I think it fell down while someone was driving maybe. I didn't measure it but there may be room for the rear side of the tire to set right on top of the receiver tube and then I can make some sort of a bracket for the front side.

    Miller 211 A.S. and Spoolmate 100
    Stickmate LX 235 AC / 160 DC.
    Clarke 180 EN Just in case
    Spectrum 375 X-Treme.
    O/A Medium Radnor Torch, Large Victor Torch.
    Milwaukee 14" Chop Saw.
    4 x 6 Horizontal Band Saw.
    Rockworth 80 Gallon 2 Stage 16 SCFM @ 175 PSI , 15 SCFM @ 90 PSI.
    Jackson Passive shade #5 for the plasma.
    I almost forgot the Hobart XVP AD Hood.


    Projects and Misc Albums
    http://picasaweb.google.com/keesfriend Feel Free to Have a Look ( Just keep in mind I am an amateur )

  7. #7
    Join Date
    Oct 2008
    Location
    Oregon
    Posts
    193

    Default

    Looks good and it should outlast the gas tank and frame.
    Millermatic 211 AutoSet w/MVP
    Century 110 volt 90/110 MIG-Gone to my son, in Texas
    Victor SuperRange OA
    Milwaukee Cold Cut Saw
    Milwaukee Portable Deep Cut Bandsaw
    Milwaukee Hole Hawg
    Jet Horizontal/Vertical Bandsaw
    Jet MD-18 Mill Drill
    Orbit Drill Press
    12 Ton Floor Press
    2002 E-350 V-10:
    1983 F-150 4.9L 6
    2004 Honda ST1300
    2007 Suzuki LTA400F Quad
    1997 Suzuki DR650

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 82

Welding Projects

Special Offers: See the latest Miller deals and promotions.