depending on the age of the vessel..I have welded many "vibration" cracks in compressor tanks. Just clean the area...stop drill it and tig it. But, if the tank is an older tank, as has been brought out, there more than likely are other stress cracks that cannot be detected and in such case the tank should be replaced.
Results 21 to 30 of 33
01-28-2009, 04:06 AM #21
welding preasure tank
01-29-2009, 05:44 PM #22Senior Member
- Join Date
- Jan 2008
- In wal-mart
Im my experience, linear cracks develop on old tanks, probably due to the expansion and contraction of the tank on a daily basis when in operation. Old tanks are out of the question, and I wouldnt even attempt it, but I would weld cracked new tanks all day long!
01-29-2009, 09:23 PM #23
Iraqi welderEquipped with red and blue... and red and green!
80% of failures are from 20% of causes
Never compromise your principles today in the name of furthering them in the future.
"All I ever wanted was an honest week's pay for an honest day's work." -Sgt. Bilko
"We are generally better persuaded by reasons we discover ourselves than by those given to us by others." -Pascal
"Since we cannot know all that there is to be known about anything, we ought to know a little about everything." -Pascal
01-08-2010, 12:29 AM #24Member
- Join Date
- Dec 2009
This thread makes me rethink my homemade sandblaster made from an old semi-rusty propane tank.
01-08-2010, 03:01 AM #25
How much pressure is going to be in your's ?
I Don't think I would worry about it !
Sunrise Outside My Shop In Delhi, Ontario
- Weldcraft WP26FV Tig Torch setup.
- Arcair- K 4000 CAC.
- LN-25 Wire Feeder
- Lincoln Ranger 8- Engine Drive- CC\CV:
- Miller Econo Twin AC/DC High Freq.
- Lincoln Power Mig 180C
- Horizontal Steel Band Saw
- DeWalt Chop Saw .
- DeWalt Compressor - 13cfm, @ 100 psi.
01-08-2010, 04:46 PM #26
Darwin Award Winner!
Kind of off topic, but tanks and explosions made me think of an item in the news just the other day.
This kid was stealing gasoline from his uncle's truck, it was early in the morning and dark. He wasn't sure how full his gas can was getting. Being the Darwin Award Nominee that he is, he thought it would be a good idea to see how full his can was by illuminating the gas can with his cigarette lighter. This resulted in burns over 75% of his body.Miller Syncrowave 200
Homemade Water Cooler
60 year old Logan Lathe
Select Machine and Tool Mill
More stuff than I can keep track of..
01-08-2010, 06:15 PM #27Senior Member
Blondie (Owner C & S Automotive)
- Join Date
- Feb 2007
- West Farmington, OH
Colt the original point & click interface!
Millermatic 35 with spot panel
Victor O/A torches
Too many other tools to list
03 Ram 1500
82 GL1100 Interstate
02-24-2010, 02:48 AM #28Senior Member
- Join Date
- Feb 2010
- Houston, Tx.
Don't do it!
You are correct to have dirtied your shorts and ceased operation. The most dangerous thing in the world is people that base saftey on the fact that they have never seen something happen. I used to be an air compressor technician for a living. I don't have the pictures to show it but have seen the results of a ruptured tank; It was a mobile unit in the bed of a 3/4 ton truck. The failure destroyed the truck. just for details a gasoline powered compressor has a control called a pilot valve that unloads the pump and controls the engine idler. Pilot valves fail all of the time; That's why there is saftey relief valve on the tank to prevent an over pressure situation. The saftey valve had failed, and to save a couple of bucks the owner installed a pipe plug in it's place. The pilot valve failed soon after and the compressor ran until the tank ruptured. Had the owner not been 300 ft. away using a paint gun he would be STONE COLD DEAD!!! Compressor tanks are assembled using submerged arc process at the factory and hydrotested at 1.5 times max working psi. You cannot duplicate these conditions; Scrap that tank and buy an new one. Remember 175 lbs is pounds per square inch. Multiply 175 by the number of square inches in your tank. Whole new respect!
02-24-2010, 08:41 AM #29Senior Member
- Join Date
- Jun 2004
02-24-2010, 01:07 PM #30
Build a smoker or a grill, do not attempt to use it! I just scored a 30 gallon tank from work that started leaking, when we cut it open there was crud in the bottom almost 2 inches deep the entire length of the tank. It had been drained but the drain was off set from the middle and there was always water left in the tank.
DW Metalworks LLC
Miller Trailblazer 302
Miller 8RC Feeder
Miller Passport Plus
Miller Dynasty 200 DX W/Coolmate 1
Hobart Handler 135
Hypertherm PowerMAX 30
Smith O/A Torch Set
Plus more tools then my wife will ever know about....