Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Page 1 of 8 123456 ... LastLast
Results 1 to 10 of 71
  1. #1
    Join Date
    Jan 2009
    Location
    Southern california
    Posts
    1

    Default Operators manual for Airco welder

    Im looking for operators manual and wiring diagram for an Airco welder model No 3A-DDR 224 HPA/BD SN S423575. I believe it was made by Miller. ( it has parts that are similar to parts in my Dialarc HF-P and some are labeled Miler) Can anyone direct me to a source? Thanks!
    Last edited by cessna195; 01-01-2009 at 09:19 PM. Reason: languuage

  2. #2
    Join Date
    Sep 2005
    Location
    Appleton, WI
    Posts
    383

    Default

    cessna195,

    I checked my cross reference chart and it looks like the unit you have there crosses over to a 330 A/B/SP, the S serial number would be a 1967 model. You can contact our manuals department at (920)-735-4356 to see if the manual is still available.
    Kevin Schuh
    Service Technician
    Miller Electric Mfg. Co.

  3. #3
    Join Date
    Dec 2008
    Posts
    9

    Default Looking for manual also

    I too am looking for some literature for an Airco welder. The model # looks to be the same (3A/DDR-224 HPA/B-D), but the Serial number looks a little different, it is 72-604573, and the stock # is 1341-0118. Does this welder also cross with the same Miller welder (330 A/B/SP)?

    Thanks,
    Justin

  4. #4
    Join Date
    Nov 2003
    Posts
    3,059

    Default Pdf

    Cesna195
    try this link and see how close this manual is

    http://www.millerwelds.com/om/o340d_mil.pdf

    this is for a 1975 vintage machine ,,, was unable to retrieve one that matched your serial...

    off topic: C195s are one of the prettiest birds out there... that Jacobs Radial makes a unique song that you can tell for a long distance... have not heard one in a lotta years.. (there was a polished and turquoise one in ABQ years ago... until the owner groundlooped it... too bad)

    hope this helps
    Heiti

  5. #5
    Join Date
    Sep 2005
    Location
    Appleton, WI
    Posts
    383

    Default

    Justin,

    Your machine crosses over to a Miller 330 A/BP Miller with a stock number of 901041. It was built in in the first half of 1972. You can contact our manuals department at (920)-735-4356 to see if the manual is still available.
    Kevin Schuh
    Service Technician
    Miller Electric Mfg. Co.

  6. #6
    Join Date
    Jun 2010
    Posts
    3

    Default Airco Literature?

    I too am looking for some literature for an Airco welder.
    The model # 2.2 ADG-AMEL-A
    and Serial number is: S435310
    Thanks,
    Dean

  7. #7
    Join Date
    Sep 2005
    Location
    Appleton, WI
    Posts
    383

    Default

    Dean,

    I could not find a 2.2 ADG-AMEL-A in my cross reference, could it be a 2.25?
    Kevin Schuh
    Service Technician
    Miller Electric Mfg. Co.

  8. #8
    Join Date
    Jun 2010
    Posts
    3

    Default

    I'll have to check - it's a gas powered unit - would 2.25 make sense with the rest of the numbers?

    225 Amp A.C. "Wasp"
    Weld and Power Generator
    Air Reduction
    N.Y., N.Y., USA

    The engine is:
    Onan - Division of Studebaker Corp.
    Model - CCK-MS/1196G
    Serial - 117CA04386

  9. #9
    Join Date
    Sep 2005
    Location
    Appleton, WI
    Posts
    383

    Default

    Yes, that would make sense with the rest of the description. The 2.25 model crosses over to a Miller AEA-200 LE engine drive. The "S" serial number puts it at a 1967 model.
    Kevin Schuh
    Service Technician
    Miller Electric Mfg. Co.

  10. #10
    Join Date
    Jun 2010
    Posts
    1

    Default

    I'm also looking for some info on an Airco welder.

    It was advertised on a local buy an sell. This is all the info I have.

    450 Amp Airco Mig

    Airco RG909001.

    Any help would be really appreciated.

    Here's the attached picture,

    Last edited by Eric N; 06-24-2010 at 08:34 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 82

Welding Projects

Special Offers: See the latest Miller deals and promotions.