Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Results 1 to 10 of 22

Hybrid View

  1. #1
    Join Date
    Sep 2008
    Location
    Omaha, NE
    Posts
    447

    Default Can some one pass me a shoe-horn! Long post with tons of pics..56k beware!

    Well, one of my favorite things to do is race motorcycles..All sizes, and since the rash of bad get-offs at 130+ in my early 20's i've found a nice little sport that's not only affordable and fun to build your won creations, but there's actually races for them too!

    The first pics are of one i started on for a customer just recently. IT came to me as a fully assemble 2005 Honda CR-85cc dirtbike. (with a blown bottom end) A few days ago I stripped the old motor, plastics, radiators and everything else off in getting ready to fi the brand new 250cc motor the owner had shipped to my house after dropping the bike off. Once this motor is in, I'm doing some port work, Crower will do the cam, Trail bikes HC piston (13.5:1 or so) and then I'm going to De-stroke it so it will rev like no 4 stroke 238cc bike you've seen I will post vids when i'm done

    here's the first ones... the vids i'll post later are where we do shows for the J.D.R.F. And the A.C.S (diabetes and cancer societies...we do shows of stunting and jumping for the kids that are at the camps all over the US in the summer...one of the most rewarding things i've ever done for free..or paid to do actually)

    Anyway... I aint here bout no jibber jabber LOL and here's where it gets long with pictures hope yo're nto on dial up HAhahaha

    the first 6 or so are the CR85 w/ 250 motor


    Dynasty 200DX
    Hobart Handler 135
    Smith MB55A-510 O/A setup
    Lathe/Mill/Bandsaw
    Hypertherm Powermax 45
    Just about every other hand tool you can imagine

  2. #2
    Join Date
    Sep 2008
    Location
    Omaha, NE
    Posts
    447

    Default



    here's where iw as just trying to figure out how to set it


    it's going to be a close fit for the pipe

    These 2 were taken around midnight tonight when i finally called it quits. This is probably aboue exactly how the motor will sit, now i just have to biuld soe mounts, a cradle, re0enforce teh upper frame i hacked up and put it back together..yea thats easy enough LOL
    Dynasty 200DX
    Hobart Handler 135
    Smith MB55A-510 O/A setup
    Lathe/Mill/Bandsaw
    Hypertherm Powermax 45
    Just about every other hand tool you can imagine

  3. #3
    Join Date
    Sep 2008
    Location
    Omaha, NE
    Posts
    447

    Default



    Here's some of my other builds for stunting and racing.. Both the red/black bike and the green rat rod were piles of rusted up junk in a garage...we got a pair fo them for 200 bucks, then a lot of time and effort later, i built the red and black one for my buddy (did all the fab and paint..was his mental idea though) And the green rat rod (a.k.a. project good will..a.k.a. the grenade) is my baby! it was a pile of junk, i call it roject goodwill because the frame was given to me for the work i did on the red bike, and the motor (125cc when it was stock) was donated for some work for the owner of the first bike in this thread ( i build and tune his real moto-x race motors ) THe gren bike boasts over 15 HP, in a 115lb bike lots of custom parts from cams to pistons..one offs aren't cheap either..that's where i spent all my money since i got the rest for doing what i love and just had to paint and build it

    Last edited by turboglenn; 12-15-2008 at 02:09 AM.
    Dynasty 200DX
    Hobart Handler 135
    Smith MB55A-510 O/A setup
    Lathe/Mill/Bandsaw
    Hypertherm Powermax 45
    Just about every other hand tool you can imagine

  4. #4
    Join Date
    Sep 2008
    Location
    Omaha, NE
    Posts
    447

    Default

    The green one before i got a pipie built. and trying on a new seat.. if you look close ALL the welds are smoothed over with bondo on the frame...talk about time 8)





    Dynasty 200DX
    Hobart Handler 135
    Smith MB55A-510 O/A setup
    Lathe/Mill/Bandsaw
    Hypertherm Powermax 45
    Just about every other hand tool you can imagine

  5. #5
    Join Date
    Sep 2008
    Location
    Omaha, NE
    Posts
    447

    Default

    And here's some of my street girl, a glance of the one that made me a cripple for life and evena pic of the one i stunt at the shows we do ( you can see accessories on it for doing different trick combos) There's even 2 of my wifes bike after geting some chrome and a pic her beuatiful self as well (and had to throw in the 2 other things i love,,,guns and my car on slicks )





    Dynasty 200DX
    Hobart Handler 135
    Smith MB55A-510 O/A setup
    Lathe/Mill/Bandsaw
    Hypertherm Powermax 45
    Just about every other hand tool you can imagine

  6. #6
    Join Date
    Sep 2008
    Location
    Omaha, NE
    Posts
    447

    Default

    Fnally, the wife's bike and her in her belly dancing costume yum enjoy




    This is the one that crippled me... 135 MPH was all i could slow to by the time i made impact...I'm very lucky to be here, but i'll never stop riding, only ride smarter.. I'm leaving it a link because i think it's huge
    http://members.cox.net/turboglenn/WreckedF3.jpg
    Dynasty 200DX
    Hobart Handler 135
    Smith MB55A-510 O/A setup
    Lathe/Mill/Bandsaw
    Hypertherm Powermax 45
    Just about every other hand tool you can imagine

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 82

Welding Projects

Special Offers: See the latest Miller deals and promotions.