I build this roll bars for a c3 convertible corvettes, that fit in years 1968-1975 models.this are made out of aluminum sch 40, which I used my hossifeld bender #2,I also used my lincoln 300amps tig welder to weld my roll bar.
Results 1 to 10 of 19
Thread: roll bars
06-30-2008, 07:13 PM #1Junior Member
- Join Date
- Jun 2008
06-30-2008, 10:33 PM #2Junior Member
- Join Date
- Dec 2007
07-03-2008, 09:41 AM #3Senior Member
- Join Date
- Apr 2007
like wearing silver ear rings instead of a full face helmet
07-03-2008, 12:39 PM #4Senior Member
- Join Date
- Jan 2008
You could also use PVC water pipe and paint it silver. Less cost and same outcome. Please don't take offence to the comments. Your welds look nice but the materials selected and geometry used are most unfortunate.
There was company out in CA that was selling roll bar kits to the street tuner kids called "Monkey Bars". They might still be selling them. They sold two kinds of kits IIRC. One was made from plastic water pipe that the user cut and glued into the car then covered with roll bar foam to hide the fact that the bars were fake. The other was made from swing set or thin wall elec conduit type seamed junk that came pre painted ready to glue/screw to the car.
Last edited by Vicegrip; 07-03-2008 at 12:44 PM.Weekend wannab racer with some welders.
07-03-2008, 12:59 PM #5
dem be called 'Show Bars"Ed Conley
Passport Plus w/Spool Gun
Miller 125c Plasma 120v
SO 2020 Bender
You can call me Bacchus
07-03-2008, 01:36 PM #6
I have to agree with all the previous posts except #1....I calzem as I seezem
maybe they could be reinforced with balsa wood????????????Nick
Miller 252 Mig
Miller Cricket XL
Millermatic 150 Mig
Miller Syncrowave 200 Tig
Jet Lathe and Mill
Jet 7x12 horz/vert band saw
DeWalt Multi Cutter metal saw
Century 50 Amp Plasma Cutter
20 ton electric/hydraulic vertical press
60" X 60" router/plasma table
Vist my site: www.nixstuff.com
and check out some of my ironwork and other stuff
07-03-2008, 02:05 PM #7
Now hold on guys.
Once upon a dead racer Porsche made monococks from aluminum tube and sheet aluminum. after sever deaths and some angry competitors they went back to a more durable construction material. Vary fast cars btw
07-03-2008, 02:34 PM #8"Better Metalworking Through Research"
Miller Dynasty 300DX
Miller Dynasty 200DX
Miller Spectrum 375 extreme
Miller Millermatic Passport
Miller Spot Welder
Motor-Guard stud welder
Smith, Meco, Oxweld , Cronatron, Harris, Victor, National, Prest-o-weld, Prest-o-lite, Marquette, Century Aircraft, Craftsman, Goss, Uniweld, Purox, Linde, Eutectic, and Dillon welding torches from 1909 to Present. (58 total)
07-03-2008, 02:43 PM #9
I would not want to be the driver of that vette, no offense. When I built my rollbar, I was having a tough time using the .134 ERW steel tubing that was supplied in the kit. I was expecting DOM tubing....
But Aluminum, just doesnt cut it in my opinion.Voigt Precision Welding, Inc.
Miller Dynasty 200 DX, Miller Syncrowave 250, MillerMatic 252, Hypertherm Powermax 45, Auto Arc Trailpower 8000,272+187 lb Peter Wright anvil, 120 lb Fisher-norris, and more! Buffalo drill press, Grizzly Horiz. Bandsaw, Edwards shear, Barth Shear, bantam mechanical ironworker, Hopkins fly press, Doall Bandsaw, brown and sharpe surface grinder.
2007 Silverado 2500HD (tow vehicle)
2000 Camaro SS (Race car)
07-03-2008, 02:44 PM #10