Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 30
  1. #11
    Join Date
    Jul 2008
    Location
    Delhi, Ontario:
    Posts
    1,968

    Exclamation S.S. Mig Gas ?

    Quote Originally Posted by davedarragh View Post
    C-25 or 100% CO2 can be used with most types of gas shielded flux cored SS wire.

    98% argon/ 2% O2 for metal cored

    SS MIG wire, depending on type, uses 95/5 CO2, 97/02 or Tr-Mix 90H/7.5Ar/2.5 CO2 for short arc and 98 Ar/ 2% O for axial spray transfer.

    Know your metals and your wire for correct application

    Dave
    Dave, I'll be doing a small restaurant job ( cracked dividers S.S. ) and I'll be using C-25, Should be allright small downhand Welds ? ( In a Sink )
    P.S. , Here anything about the Hockey Team- Bankruptcy hearing today ??

    ............... Norm

    Sunrise Outside My Shop In Delhi, Ontario

    - Arcair- K 4000 CAC.

    - LN-25 Wire Feeder

    - Lincoln Ranger 8- Engine Drive- CC\CV:



    - Lincoln Power Mig 180C
    - Spoolgun.
    - DeWalt Chop Saw .
    - DeWalt Compressor - 13cfm, @ 100 psi.

    www.normsmobilewelding.blogspot.com

  2. #12
    Join Date
    Oct 2007
    Posts
    2,949

    Default SS MIG & NHL Follies

    Hey Norm: Food grade is usually 316 isn't it?

    FCP-316L is all position EXCEPT vertical down.

    What kind of wire do you have?

    The Federal Bankruptcy Judge ordered both sides to a Mediation Hearing on May 27th.

    The drama continues................

    Dave
    "Bonne journe'e mes amis"

  3. #13
    Join Date
    Jul 2008
    Location
    Delhi, Ontario:
    Posts
    1,968

    Default

    Quote Originally Posted by davedarragh View Post
    Hey Norm: Food grade is usually 316 isn't it?

    FCP-316L is all position EXCEPT vertical down.

    What kind of wire do you have?

    The Federal Bankruptcy Judge ordered both sides to a Mediation Hearing on May 27th.

    The drama continues................

    Dave
    Dave, I'll be using 308L hard wire !
    Mediation Hearing? Crazy I Say Crazy !! You watch Bettman will Keep them In
    The U.S.A., He's an IDIOT !!

    .... ........... Norm

    Sunrise Outside My Shop In Delhi, Ontario

    - Arcair- K 4000 CAC.

    - LN-25 Wire Feeder

    - Lincoln Ranger 8- Engine Drive- CC\CV:



    - Lincoln Power Mig 180C
    - Spoolgun.
    - DeWalt Chop Saw .
    - DeWalt Compressor - 13cfm, @ 100 psi.

    www.normsmobilewelding.blogspot.com

  4. #14
    Join Date
    Oct 2007
    Posts
    2,949

    Default SS MIG Wire

    Hey Norm: 308L is for "18-8" (304) steels. It calls for Tri-Mix in short arc transfer. 90% He/ 7.5% Ar/ 2.5% CO2.

    Vertical Up and overhead (3F, 3G, 4F, 4G, 5G, 6G) for solid SS MIG wire.

    Yeah, Moyes owns Swift Transportation (they probably run up your way), and rumor has it, he's had some financial issues for a while now.

    We'll see where the ice melts, and refreezes.

    As they say "The Puck Stops Here"
    "Bonne journe'e mes amis"

  5. #15
    Join Date
    Jul 2008
    Location
    Delhi, Ontario:
    Posts
    1,968

    Default

    Quote Originally Posted by davedarragh View Post
    Hey Norm: 308L is for "18-8" (304) steels. It calls for Tri-Mix in short arc transfer. 90% He/ 7.5% Ar/ 2.5% CO2.

    Vertical Up and overhead (3F, 3G, 4F, 4G, 5G, 6G) for solid SS MIG wire.

    Yeah, Moyes owns Swift Transportation (they probably run up your way), and rumor has it, he's had some financial issues for a while now.

    We'll see where the ice melts, and refreezes.

    As they say "The Puck Stops Here"
    Dave; Well, It's a Small Job, and 308L & C-25 are what I have ! There's No Way I'm buying Tri-Mix for this small job !

    Ya, Bettman is trying to say the N.H.L. took over control of the team last Nov. - Dec./08 . We'll have to wait & See what happens. But there is No Way He'll let that Team come Back to Canada, It was in Winnipeg till "96" I think !

    ................ Norm

    Sunrise Outside My Shop In Delhi, Ontario

    - Arcair- K 4000 CAC.

    - LN-25 Wire Feeder

    - Lincoln Ranger 8- Engine Drive- CC\CV:



    - Lincoln Power Mig 180C
    - Spoolgun.
    - DeWalt Chop Saw .
    - DeWalt Compressor - 13cfm, @ 100 psi.

    www.normsmobilewelding.blogspot.com

  6. #16
    Join Date
    Jan 2008
    Location
    very eastern MA
    Posts
    114

    Default

    Quote Originally Posted by nfinch86 View Post
    Dave; Well, It's a Small Job, and 308L & C-25 are what I have ! There's No Way I'm buying Tri-Mix for this small job !


    ................ Norm
    Id tig it

    the co2 will help the weld rust over time

  7. #17
    Join Date
    Mar 2007
    Location
    Deltaville, VA
    Posts
    2,239

    Default

    Hey Dave,

    Know it's a typo but you may want to check your tri-gas mix in post #10.

    I "hope" some newbie doesn't try a 90% Hydrogen mix.

  8. #18
    Join Date
    Oct 2007
    Posts
    2,949

    Default

    Quote Originally Posted by SundownIII View Post
    Hey Dave,

    Know it's a typo but you may want to check your tri-gas mix in post #10.

    I "hope" some newbie doesn't try a 90% Hydrogen mix.
    Sundown: Hey Thanks, forgot the "e"

    Hopefully no one will try it, I doubt if they could find anyone to fill that recipie!

    Thanks again, I think I need to clean my keyboard!

    Dave
    "Bonne journe'e mes amis"

  9. #19
    Join Date
    Jul 2008
    Location
    Delhi, Ontario:
    Posts
    1,968

    Default

    Quote Originally Posted by gordfraser View Post
    Id tig it

    the co2 will help the weld rust over time
    I Do Not Tig.!

    ............. Norm

    Sunrise Outside My Shop In Delhi, Ontario

    - Arcair- K 4000 CAC.

    - LN-25 Wire Feeder

    - Lincoln Ranger 8- Engine Drive- CC\CV:



    - Lincoln Power Mig 180C
    - Spoolgun.
    - DeWalt Chop Saw .
    - DeWalt Compressor - 13cfm, @ 100 psi.

    www.normsmobilewelding.blogspot.com

  10. #20
    Join Date
    May 2009
    Location
    Ottawa Canada
    Posts
    494

    Default Vertical up hand?

    Norm,

    if you want help with uphand solid wire steel or ss let me know.I'll show you the ancient frenchman secret technique LOL.You'll quickly make it have the stack of dimes look,just like i was talking about when i called you,Frank
    Millermatic 252
    Millermatic 180
    Dynasty 200DX
    Hobart spoolmate 3035
    Digital Elite

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 82

Welding Projects

Special Offers: See the latest Miller deals and promotions.