Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums
 
Miller Welding Discussion Forums - Powered by vBulletin

Page 1 of 2 12 LastLast
Results 1 to 10 of 17

Hybrid View

  1. #1
    Join Date
    Feb 2006
    Location
    NW Montana
    Posts
    7

    Default Need ideas for welding table

    hello, I am a new member and after reading the project board for about the last week to get ideas on my new table i thought i would join and ask for some.

    I am building a 36"x27"x3/8" welding table with a fold up 12" extention on one end and 12" fold up cutting grate on the other (i have limited space so i want it to be somewhat colapsable.) it will also have a craftsman intermediate style tool chest mounted under the table top for storing tools and i was also considering a reciever style setup to accept a vice/bender or other misc. attachments that could be mounted to a plate and then slid in and removed to acomidate the job i would happen to be doing. (i got the reciever idea off of the message board) any sort of ideas or advice would be apreciated and i will try to get some pics posted of what i have so far.

    thanks, Nick

  2. #2
    Join Date
    Sep 2005
    Location
    northern NJ
    Posts
    1,847

    Default

    Height is personal preference. My table is 32" from floor to top. For most things it works well for me. Did a tig job the other day & I wished it was a little taller. Mine is 1" thick 48 x 96 top with 4 ship channel frame & legs. 6" hd casters for mobility. Make sure you leave a lip of a couple inches all around so it is easy to clamp stuff to.---MMW---
    MM250
    Trailblazer 250g
    22a feeder
    Lincoln ac/dc 225
    Victor O/A
    MM200 black face
    Whitney 30 ton hydraulic punch
    Lown 1/8x 36" power roller
    Arco roto-phase model M
    Vectrax 7x12 band saw
    Miller spectrum 875
    30a spoolgun w/wc-24
    Syncrowave 250
    RCCS-14

  3. #3
    Join Date
    Sep 2005
    Location
    S.W. Pennsylvania
    Posts
    2,250

    Default

    My table is also about 32" . This seems to be a good all a round hight. I have worked on 36" tables and found them to be uncomfortable , especially on large projects. Then again, I'm a short person so it all comes down to personal preferance. I drilled and threaded holes for my vice and other equipment so it can be unbolted easily without haveing to hold a nut on the other side.
    To all who contribute to this board.
    My sincere thanks , Pete.

    Pureox OA
    Westinghouse 300 amp AC stick
    Miller Syncrowave 250
    Hexacon 250 watt solder iron

  4. #4
    Join Date
    Feb 2006
    Location
    Eastern Washington
    Posts
    14

    Default

    I've found 32-33" to be a pretty common height for tables. We just built a couple 4'x8' tables for our school shop out of 1/4" top plate, 4" channel (1/4" wall) for the frame/crossbraces and 4" x 4" (10 gauge) for the legs, plus 1/4" plate for gussets on the legs. We also welded on HD braking casters so we can move them around the shop. Seem to work well and heavy enough for our use. May someday through another 1/4" plate on top...but not anytime soon...I'll see if I can dig out the digital camera and snap some pics soon..

  5. #5
    Join Date
    Oct 2005
    Location
    Calgary, AB
    Posts
    52

    Default If you're tall go a little higher

    32" is pretty much the standard height, but if you're taller than average, go a little higher, your back will love you. I'm 6'3 and my table is 34". It keeps me from hunching over that little bit. Anyone who's tall will know what I'm talking about. I end up getting a sore back just doing the dishes, but with just a couple of extra inches on my table, I can weld all day. I even custom built my own desk for my office that sits 1" taller than standard. It forces me to sit up proper in my chair, so I don't hunch over my keyboard.
    That's what's great about us fabricators, if it don't work right for us, we can make it!
    The difference between No One. and No. One is where you put the period. John Force

  6. #6
    Join Date
    Feb 2006
    Posts
    411

    Default

    I think the reciver idea will be a plus you could mount a female pice in the up-right position and the weld a mail piece on a plate then bolt your vise to the plate. just drop you vise in the reciver and their you have a vise on the edge or side of your table
    this way you can move it if you need to.
    also you can get 4 big nuts and bolts, like inch and a half bolts and nuts
    weld the nut to a plat and screw the bolt into the nut, mount the plate on the botom of your leg of your table and then if the floor in your shop,work area is uneaven you can turn the bolts to eather raise or lower the table to compinsate for the floor and then your table will be level (note table will be sitting on bolt heads) and you can level it where ever you put it.
    if you were to mount your table on casters you could make it where your bolts could be screwed down low enuff to rase it to level it.
    I hope all these ideas help you to make a great table
    have fun

  7. #7
    Join Date
    Nov 2005
    Posts
    109

    Talking Welding Table

    Quote Originally Posted by WeldTeach
    I've found 32-33" to be a pretty common height for tables. We just built a couple 4'x8' tables for our school shop out of 1/4" top plate, 4" channel (1/4" wall) for the frame/crossbraces and 4" x 4" (10 gauge) for the legs, plus 1/4" plate for gussets on the legs. We also welded on HD braking casters so we can move them around the shop. Seem to work well and heavy enough for our use. May someday through another 1/4" plate on top...but not anytime soon...I'll see if I can dig out the digital camera and snap some pics soon..
    HelloIve been welding for a few years and I have built several tables all are about 32 inches high
    the best thing I have built onto them is a sliding tool holder on all 4 corners this is a tube inside a tube that makes the table frame
    I slide it out to hold my Lead or Vise Grips or C clamps
    when I need it when not needed I slide it in hidden from view and also doesnt interfere with top of table, these sliding tool holders also serve as a torch table when I slide them and locate a piece across both of them so slag will fall to floor.
    I also have a shelf at about 10 inches from floor for fixtures and a smaller one about 6 inches from top for grinder or other tools
    I will post a pic as soon as I can remember to take it with me to the shop
    also I have an air hose hanger next to my blue print table and on the other side I have Oxygen acetylene bottles with a hose and torch holder"
    the hose reel is on a stand and it also hold my 4 1/2 grinder on a piece of 4 " channel
    keeping out of the way hope I helped you some what
    Santiago Nunez

  8. #8
    Join Date
    Dec 2005
    Posts
    375

    Default Sliding tool holder

    Quote Originally Posted by SNUNEZ

    the best thing I have built onto them is a sliding tool holder on all 4 corners this is a tube inside a tube that makes the table frame
    I slide it out to hold my Lead or Vise Grips or C clamps
    when I need it when not needed I slide it in hidden from view.
    Santiago Nunez
    I'm glad you shared this..I really like the sliding tool holder idea. I'm planning on building a new table this spring and I'll pencil this into the sketch.
    Thats what's nice about these forums..you can get all kinds of good ideas from fellow members that already have something you're needing adeas on.
    Thanks again, Farris
    Gone But Never Forgotten!

  9. #9
    Join Date
    Feb 2006
    Location
    Eastern Washington
    Posts
    14

    Default

    Quote Originally Posted by SNUNEZ
    HelloIve been welding for a few years and I have built several tables all are about 32 inches high
    the best thing I have built onto them is a sliding tool holder on all 4 corners this is a tube inside a tube that makes the table frame
    I slide it out to hold my Lead or Vise Grips or C clamps
    when I need it when not needed I slide it in hidden from view and also doesnt interfere with top of table, these sliding tool holders also serve as a torch table when I slide them and locate a piece across both of them so slag will fall to floor.
    I also have a shelf at about 10 inches from floor for fixtures and a smaller one about 6 inches from top for grinder or other tools
    I will post a pic as soon as I can remember to take it with me to the shop
    also I have an air hose hanger next to my blue print table and on the other side I have Oxygen acetylene bottles with a hose and torch holder"
    the hose reel is on a stand and it also hold my 4 1/2 grinder on a piece of 4 " channel
    keeping out of the way hope I helped you some what
    Santiago Nunez
    Sounds like cool ideas. I'm a "visual" guy though...I'd like to see some pics!!

  10. #10
    Join Date
    Feb 2006
    Location
    NW Montana
    Posts
    7

    Default

    Thanks everyone for the info so far. I think that 32" sounds like a good hight i am a pretty short fella so that should work out for me. i am also planning on mounting casters to the legs and having screw down feet to lift it off the casters and make it stationary and level. my next challenge will be designing the mechanism to hold the folding ends up. i will try and take some pics and post them tomorrow (2-9-06) to explain what i am up to here.

    i am also considering a HF compact bender which is on sale for $49.99 on the net right now and adding the scroller attachment...i know that the scroller takes a little work to get opperable but the SO one is out of my range for now but i was wondering if anyone had anything to say about the HF compact bender (pos or neg) any coments would be appreciated.

    Thanks again and weld on ! Nick

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Non-static method PhpQuickProfiler::getMicroTime() should not be called statically in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/pqp/classes/Console.php on line 77

Warning: Function split() is deprecated in /mnt/stor3-wc1-dfw1/357822/357839/www.millerwelds.com/web/content/lib/footer.inc.php on line 82

Welding Projects

Special Offers: See the latest Miller deals and promotions.