I've been thinking about this a while. Miller needs to come out with a wireless foot pedal for there tig welding machines. It's such a pain in the rear when you have I don't know how many electrical cords all tangled up around you and your torch but for whatever reason for me it is the dam foot pedal that bugs me. Seems like I'm always curled up like a pretzl in some kinda vessel or welding pipe on a vessel and this dang foot pedal is tangled up everywhere. so yeah come on guys come up with a wireless remote foot pedal I think other will agree it would be nice. I know some of you may say oh use a hand control well I have they s*ck I don't like them
Results 1 to 10 of 32
02-25-2008, 10:17 PM #1
Miller guys come up with a wireless foot pedal for the tig welder???
02-25-2008, 10:34 PM #2Senior Member
- Join Date
- Feb 2008
- flat , and lots of dirt
Looking at the schematics of my foot control.................
It would take about $250 worth of parts from Parallax(bluetooth Rx & Tx stuff,and a processor or two to run it all)..........
And finding someone on Parallax.com's message board to get this done, which might be costly also.
Dont know for sure if that'll work in the presence of an arc either.
Actually I would prefer a helmet that reads your thoughts and shapes the arc and controls the amps and all that good stuff, but I think that one is still a few years off tho.SYNCROWAVE 200
Atlas 618 lathe (vintage 1960) reconditioned DC
Sioux 3/8 Pneumatic Reversible Drill
Makita Everything else
2400 square feet of Sanford and Son lookin shop space
"Once the spoon flys, putting the pin back in won't solve anything"
USA 15T, 15V
http://i100.photobucket.com/albums/m...5/DSC00356.jpg two cans, one welder
02-25-2008, 10:49 PM #3
Considering the HF arc starter is enough EMI to trip arc fault GFI outlets within 8ft, I'm thinking radio controlled amptrols have a distinct operating problem.
I used to think it was due to the circuits the welder shared with the sub panel, but today I tripped a pair of them on the other wall which isn't fed by anything remotely tied to the welder sub panel. Then again, maybe Leviton made them too sensitive.Syncrowave 250DX
XR Control and 30A
Airco MED20 feeder
Thermal Dynamics Cutmaster 81
Smith O/A rig
And more machinery than you can shake a 7018 rod at
02-25-2008, 10:57 PM #4Senior Member
- Join Date
- Feb 2007
- Olive Branch Ms
Listen up Miller, This man makes a good point. How hard could it be? I'd pay up in a second to not have to wrestle with another cord. Positioning my foot control with a wire attached to it is a pain. A remote foot control that you could attach to your boot would be awesome. Make it as small as a foot and put some resistance in it to where you really had to apply some pressure to it it to change the heat. Sounds like a good idea to me. AdamWebb's Welding and Repair LLC
MM210 w/a 3035 spoolgun
Trialbazer 302 w/HF
02-26-2008, 01:04 AM #5Guest
- Join Date
- Dec 2005
- Lodi, CA
Some of us have been waiting for the new wireless MIG gun for a couple years now,,, I think Miller really needs to get on the ball here.
02-26-2008, 01:08 AM #6
02-26-2008, 06:59 AM #7Nick
Miller 252 Mig
Miller Cricket XL
Millermatic 150 Mig
Miller Syncrowave 200 Tig
Jet Lathe and Mill
Jet 7x12 horz/vert band saw
DeWalt Multi Cutter metal saw
Century 50 Amp Plasma Cutter
20 ton electric/hydraulic vertical press
60" X 60" router/plasma table
Vist my site: www.nixstuff.com
and check out some of my ironwork and other stuff
02-26-2008, 10:26 AM #8
i watched a guy make a wireless mig welder before
he set down his stinger and moved the steel on the saw horses and PRESTO a wireless mig welder
i also have a an idea for a wireless welder interchangeable for mig,stick,and tig.....
you take a gas generator,put backpack straps on it bolt your welder to it pull on the string and start welding
Last edited by welderman23; 02-26-2008 at 10:40 AM.my daddy always said i was IRONHEADED....
feel free to P/M me
02-26-2008, 10:38 AM #9Senior Member
- Join Date
- Oct 2007
- Cave Creek Az
Hey if we are going wireless make sure they make wireless adapters for SMAW as well. The pipeline guys would go nuts for them!
As for wireless MIG, I already made one of those a little while back. It happened accidentally, like all good inventions. I was welding on a custom job in the shop and had it supported with pipe jacks. The project was eight feet tall and I needed to give it a little push up right in the middle so I placed another pipe jack on top of my welding table. As soon as I was done I released the pipe jack and subsequently knocked it off the table, right on top of my MIG lead, severing it. Viola! instant wireless MIG. The amperage seems a little low now, but that can be worked out.
02-26-2008, 10:42 AM #10