cheap welding helmet

[Homeschoolweldor]

Hey guys,

I'm thinking about buying this auto shade helmet.
http://www.northerntool.com/webapp/w...1850_200311850

Do y'all think it's a good buy for a beginner.

Thanks

[JimYoung]

well, beginner or long time welder ... you only have one set of eyes and once you fry them.. they are gone .. Compare the UV protection, darkening speed, type battries required, lense cover replacements, quality of the head gear, and anything else you can compare. I have two cheap HF Helmets, the small lense one works great, the large lens one makes my face fell like its been in the sun too long. My Speedglass one is great and a clear winner in all departments. My advice is to get the best that you can afford. In my judgement, your helmet is the most important piece of welding equipment that you will buy.. get a good one..
these look like good comparisons for low end helmets http://www.harborfreight.com/cpi/cta...emnumber=94337
http://www.harborfreight.com/cpi/cta...emnumber=94336
check their specs against Millers

Jim

[HMW]

Although that is not an expensive auto-darking helmet I think I would start with a regular one. Like a jackson or fibre-metal. In-expensive and leaves some money to spend on more tools

[dabar39]

I have tried just about every type of helmet on the market today and I'm most comfortable with my trusty old Jackson hood. It is all a matter of personal preferance. I don't care for the auto shade lens either as I have damaged a few in my day and don't really trust them to work properly all the time either. I used to do alot of stainless welding in tight areas where you had to be very close to the item being welded and heat cracked the photo cells in them more than once. Dave

[yorkiepap]

Hey Homeschool,
That helmet is a good one. I have one and have used it 12-20hrs/week for the last year and a half without any problems. It has a fast react time, sens. & delay settings, and is quite comfortable...for me. I also have 2 of the HF Blue Flame helmets that have the same specs. as this one. I believe they are made by the same company as the electronics are identical. They have been reliable and the shading adjustment works very well as I like #10 setting for MIG & #11 for TIG. They are reasonably priced and if one goes bad, I'll toss it and get another...to me they are a consumable......Denny

[Bareback Jack]

My dad bought me a HF auto hood years ago and I used it allot. When I started welding full time it broke down in no time! It was ok for occational use, but just couldn't handle hard working conditions. I replaced it with a Miller Elite and I can't beleive the difference. I was missing out! Now, if you are just the occational welder (2 times a month) the cheapy will probably work. If you are going to see allot of hood time, then I'd spring for the better hood. Your eyes are precious, treat them with care! I do notice a difference with my eyes when comparing the two hoods. The cheapy left a "red dot" in my vision for quite a while if I was under hood very long. The new hood greatly reduced this vision imparment. Good luck!

[Bmxin^Bjorn]

i agree with dabar on this one the jackson hoods are the best around
they stand up to almost anything and are pretty cheap too.
i have a bwe and it is ausome, i had it at the hitch shop for a few weeks and if i wasent watching it 24/7 it would have been distroyed by others not being careful. i think we have run over like 4 welding masks this year driving on and off the hoists... also in construction would you want to drop you miller autodark$$$$$ or you jackson$ 4 storys?..

[cajuncat]

I been having having a sellstrom for about the last 17 years and can't complain.About 10 years ago i bought a speedlens for it and wondered how I did without it.Just recently I bought the miller 29 roadster elite series and I really enjoy it.Auto-darken shields are the way to go.

[fun4now]

They are reasonably priced and if one goes bad, I'll toss it and get another...
thats the problem with too many people today, we are getting used to getting cheap crap and judt figure its ok for it to break, i'll just get another one. thats why we have soo much cheap crap out there. what ever happend to buying quality once and expecting it to last.
i got a Miller BWE about 6 years ago. i use it inside and outside. i use it for MIG,TIG,Stick and plasma cutting. it has never failed me. i would never consider trusting my eyes to a cheapo hood. how many flashes are ok ???? i say none. get a good hood.
get a good one and demand it to last, you only have one set of eyes keep them safe.

[jfsmith]

I have an HF auto darkening bucket, I also have a Fibre Metal that I like. I use the Fibre Metal one more than the HF one. I have several lenses for the Fibre Metal helmet and a set of the bifocals for it.

I wish I had a positive air flow welding helmet. You have one set of eyes and one set of lungs.

They can replace the lungs these days, but it will hurt.

Jerry