Announcement

Collapse
No announcement yet.

Search Result

Collapse
10 results in 0.0037 seconds.
Keywords
Members
Tags
  • You can also choose from the popular tags.

repair x

  • Mike yates
    started a topic Miller matic 35 sputtering

    Miller matic 35 sputtering

    Guys in shop complaining about sputtering, but welds look great to me. 85 wire feed welding 1/2 plate on setting 4. 15 to 20 flow rate on 75/25 gas. Same settings for two years. But I have to admit it doesn't "hizzle" like i remember. Just replaced all the diodes with OEM because we had some...
    See more | Go to post

  • ecc
    started a topic buying used

    buying used

    looking at a used bobcat 225 that has 1600 hours. I know they're supposed to have an average lifespan of between 2-3000 hours. Is there anything in particular to look for in terms of issues? I'm looking to use this as a starter machine for a small mobile welding business and at almost half the cost...
    See more | Go to post

  • chartman
    started a topic Saving a Spectrum 2050

    Saving a Spectrum 2050

    Hey everyone,

    I'm looking for some help. I recently picked up an old Spectrum 2050 that won't fire an arc. The power and ready light come on fine, and the gas solenoid works fine when the trigger is pushed. Pressure and air quality seems fine. The ground clamp has a good connection back...
    See more | Go to post

  • brett.campbell
    started a topic warning light on hour meter

    warning light on hour meter

    My bobcat 225 will not start...red light on hour meter comes on inside of the yellow triangle on the meter. Meter shows total hours when switched to "idle" and then -99.9 when switched to "run"...no spark when switched to "start".

    Local tech says it could...
    See more | Go to post

  • Welding repair to a crack in an excavator boom.

    I have a mini excavator - Volvo EC25. Years back I had a thumb installed, which included having someone weld a clevis bracket on the boom. The individual did a great job, only welding the vertical edges to the boom. There is now a small crack starting on the corner of the boom just above the bracket,...
    See more | Go to post

  • noloafing
    started a topic syncrowave 300 low weld output

    syncrowave 300 low weld output

    I am trying to repair a syncrowave 300 which has very low weld output (will not melt stick electrode). I have tried this machine with various settings (hi/low, AC/DC, with panel or remote control) and always the same thing. However when using the start current I can get plenty of power out, so the...
    See more | Go to post

  • techy
    started a topic Plasma Gouger

    Plasma Gouger

    Hi,
    I am new to this forum and I need some advice. We have a plasma gouger thermo dynamics. We are having problems and are at our wits end. I am needing to find out if you have any ideas of what direction to take, wether we should get this one fixed or just buy a new one. This is obsolete...
    See more | Go to post

  • Welder Repair shop seeking qualified factory service techs.

    I am wondering if anybody out there is looking for a good paying job with benefits repairing welding units. Miller and Lincoln training would be beneficial. Central Alberta, Canada is where we are located. Reply to the thread if you or someone you know may be interested. Engine drive experience would...
    See more | Go to post

  • Ridgeman
    started a topic Thunderbolt 225 sick

    Thunderbolt 225 sick

    HI,

    I purchsed my TB 225 about 1973, it has served my needs on the farmette and other general needs very well. It has been in storage in my sons barn for about 2 years. I pulled it out in January 2011 to do some welding on my snow blower. Much to my surprise I could only get (I'm guessing)...
    See more | Go to post

  • Spot welder LMSW-52 with sheared bolt for handle... repair help

    I have a Miller spot welder (model LMSW-52) and the bolt which you can tighten to put more or less pressure on the electrodes when you push down on the handle has bent and snapped in two, with "normal" use. Now that I no longer have a handle to open/close the electrodes... the spot welder...
    See more | Go to post
    Last edited by karam; 01-27-2011, 02:00 PM.
Working...
X