Announcement

Collapse
No announcement yet.

User Profile

Collapse

Profile Sidebar

Collapse
Profile Picture
kd4gij
Junior Member
Last Activity: Today, 12:10 PM
Joined: 12-20-2017
Location: St. Petersburg, Fl.
  • Filter
  • Time
  • Show
  • Source
Clear All
new posts

  • kd4gij
    replied to Millermatic 200
    Well I took the cover off to clean it up and paint it. I t looks pretty good inside.

    ...
    See more | Go to post

    Leave a comment:


  • kd4gij
    replied to Millermatic 200
    The gas tubing from the valve to the wire feeder is rotted. Do I need special tubing for it?...
    See more | Go to post

    Leave a comment:


  • kd4gij
    replied to Millermatic 200
    Well I did not have any shielding gas. But ran a couple beads with out. And it works.
    See more | Go to post

    Leave a comment:


  • kd4gij
    replied to Millermatic 200
    Well I got a chance to look at the welder today. I rotated the speed control knob a few times and tried again and the wire feeder is working now. I didn't think to try that when I looked at it at work. Good thing I probably would not have gotten it for free If it worked. This thing has been in storage...
    See more | Go to post
    Last edited by kd4gij; 01-10-2018, 04:06 PM.

    Leave a comment:


  • kd4gij
    replied to Millermatic 200
    Is it ok to unplug the positive lead at the bottom while trouble shooting the wire feeder? And will doing so make the gun not hot?

    Hear is a pick of the front.

    ...
    See more | Go to post

    Leave a comment:


  • kd4gij
    replied to Millermatic 200
    Thanks. That should help.
    I just got it home will dig into it this weekend....
    See more | Go to post

    Leave a comment:


  • kd4gij
    commented on a Visitor Message From Aeronca41
    Hi
    Thanks for the info. I got this one from work for free. It has been sitting on a shelf 12ft up in a shop with no ac. It had an old spoolmatic 1 with it. No one riley knows anything about it. I haven't had time to look into it any other than plugging it in . When I pulled the trigger on the...
    See more | Go to post

  • Aeronca41
    Aeronca41 posted a Visitor Message for kd4gij
    Marty,
    I have a service manual for an MM200 with the 4-wire feed motor. Not exactly sure what serial numbers it applies to, but probably generally applicable. Not a lot more in there than the owners manual has, but there is at least a little theory of operation. Easiest for me is to mail it...
    See more | Go to post

  • kd4gij
    replied to Millermatic 200
    Here it is. Born in 1984
    See more | Go to post

    Leave a comment:


  • kd4gij
    replied to Millermatic 200
    You have a PM I appreciate any info you have. I have downloaded the manual but it isn't much help for trouble shooting.

    Thanks Marty...
    See more | Go to post

    Leave a comment:


  • kd4gij
    replied to Millermatic 200
    O k it is a black face. And the SN starts with JE. I will have more info Tuesday when I get home...
    See more | Go to post

    Leave a comment:


  • kd4gij
    replied to Millermatic 200
    Well I don't have it home yet. I will get it the first of the weak. It has been in storage for over 10 years. I took the cover off and blew all of the dust out. Plugged it in and the wire feeder isn't working. And I could only push wire half way through the gun. I know the gun will need a new liner....
    See more | Go to post

    Leave a comment:


  • kd4gij
    started a topic Millermatic 200

    Millermatic 200

    Hi
    I am new here. I was given a millermatic 200 that has a few problems.. Does anyone know where I can download a service manual for this unit?
    See more | Go to post
No activity results to display
Show More
Working...
X