Announcement

Collapse
No announcement yet.

Longevity of Dynasty 300? hours/cycles?

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Longevity of Dynasty 300? hours/cycles?

    What is the life span of the Dynasty 300s?

    Maximum hours/arc cycles to expect?

    What do you that use them have on them?

    Thanks
    Syncrowave 250DX

  • #2
    the type of work and treatment it gets would play a huge part in that. i suspect Miller has those kind of #'s in some corporate conference room but you will not likely see them.
    thanks for the help
    ......or..........
    hope i helped
    sigpic
    feel free to shoot me an e-mail direct i have time to chat. james@newyorkmetalart.com
    summer is here, plant a tree. if you don't have space or time to plant one sponsor some one else to plant one for you. a tree is an investment in our planet, help it out.
    JAMES

    Comment


    • #3
      When you say "lifespan" what are you looking for? Until complete failure of the entire machine?? Not going to happen. If you mean until a failure, it could be a few hours (unlikely) or several thousand. If that happens you fix it and continue welding. Considering that it is used for making money (typically) you should be thinking in terms of how many arc hours it will take to pay for it self. Over the life span of the unit you will spend far more on gas, tungsten, and consumables than you dynasty.
      Dynasty 200 DX
      Millermatic 175
      Spectrum 375
      All kinds of Smith OA gear

      Comment


      • #4
        I know, but since I don't have access to this information (Considering a used Dynasty 300dx of ebay) I was trying to use what information I have which is the arc timer and arc cycles from the machines memory.

        315hr and 134,109 cycles - does this makes sense and what does this say about how the machine was used.

        315hrs seem low to me (I'd expect this machine to go into the 5000+hrs), but the 134109 arc cycles seems high and would mean 7 cycles per minute.

        For those 'true welders' (I'm just an amatuer) what does this tell me about how the machine was used?

        Push hard or not at all?
        Syncrowave 250DX

        Comment


        • #5
          now i see what your looking for. i don't see how the internals in these unit would wear, i think it proves thatthe unit is reliable. Do you know what type of welding it was used for??

          Go to the motorsports forum and ask dynasty owners to post there arc time and starts with a brief description of what it is used for and if they have had any failures. I believe the 300dx is a VERY reliable unit.
          Dynasty 200 DX
          Millermatic 175
          Spectrum 375
          All kinds of Smith OA gear

          Comment


          • #6
            Hmmmmmmmmmm

            I don't know beans about the Dynasty, but, as to general Miller longevity, I have two Miller products that are over 20 years old and still cooking. Can't beat it with a stick. If I had the bucks, I'd be all over that Dyn 300 like a bum on a baloney sammich.
            Triggerman

            Ammonia refrigeration tech
            Trailblazer 302 (yes, it's new)
            Millermatic 180 w/Autoset
            CST-250
            HF-15 High frequency
            XR15 w/Push-Pull Gun
            Victor O/A, DeWalt, North mask


            "A professional knows what to do. A craftsman knows why."

            Comment


            • #7
              sounds like it was used for a lot of short welds, hard to work it hard like that unless it was short due to over duty cycle, but that i would suspect would have caused them to sell it early, just too frustrating. so i would think it was used for tacking and or short welds. the 300 was always spoken well of, so if its working and at a good $$ go for it.
              thanks for the help
              ......or..........
              hope i helped
              sigpic
              feel free to shoot me an e-mail direct i have time to chat. james@newyorkmetalart.com
              summer is here, plant a tree. if you don't have space or time to plant one sponsor some one else to plant one for you. a tree is an investment in our planet, help it out.
              JAMES

              Comment


              • #8
                We have 6 300's and 2 350's at work. They are great machines, we bought the first one 3+ years ago and no problems with any of them yet. It's hard to say how the machine was used based on the arc starts. We weld boxs and all kinds of things at work (1/8" Alum), sometimes we make 8ft long welds. You need a pile of tacks on an 8ft weld so your arc starts will add up quickly, but when it's final weld time your giving your duty cycle a workout. Like I said we haven't had any problems, the average user will likely never make the machine break a sweat!
                at home:
                2012 325 Trailblazer EFI with Excel power
                2007 302 Trailblazer with the Robin SOLD
                2008 Suitcase 12RC
                Spoolmatic 30A
                WC-24
                2009 Dynasty 200DX
                2000 XMT 304
                2008 Thermal Dynamics Cutmaster 52
                Sold:MM130XP
                Sold:MM 251
                Sold:CST 280

                at work:
                Invision 350MP
                Dynasty 350
                Millermatic 350P
                Retired:Shopmaster 300 with a HF-251

                Comment

                Working...
                X