Announcement

Collapse
No announcement yet.

Shop equipment

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Shop equipment

    What would be the least ammount of equipment a small shop could thrive.
    Make your wish list.

  • #2
    Equipment

    The simplest Welding-shop equipment that permits you to perform your work is probably all that you need for getting started. For work on low carbon steel an example would be a simple AC transformer welding power supply. Keep in mind that used and reconditioned equipment may be available at substantial savings.

    Fancy looking machines with all sort of additional capabilities may be strongly promoted by suppliers, but the question is if they are going to help your business become more productive and successful. New equipment should be first rented or leased for a short while, to decide if it actually provides benefits.

    Besides electric welding equipment, an oxyacetylene welding kit mounted on a hand cart holding two gas cylinders is almost a must for any Welding-shop and maintenance facility. An air compressor may be needed to power pneumatic tools.

    Apart from welders you will need accessories, like disc cutters, grinders, welding table with a sturdy vise, files, hammers to remove slag etc. and of course personal protection devices like welding mask, goggles, gloves, apron and so on. See

    www.welding-advisers.com/Welding-shop.html

    Comment


    • #3
      I am confused......did you just post a question and then answer yourself???

      www.facebook.com/outbackaluminumwelding
      Miller Dynasty 700...OH YEA BABY!!
      MM 350P...PULSE SPRAYIN' MONSTER
      Miller Dynasty 280 with AC independent expansion card
      Miller Dynasty 200 DX "Blue Lightning"

      Miller Bobcat 225 NT (what I began my present Biz with!)
      Miller 30-A Spoolgun
      Miller WC-115-A
      Miller Spectrum 300
      Miller 225 Thunderbolt (my first machine bought new 1980)
      Miller Digital Elite Titanium 9400

      Comment


      • #4
        The least??? a welder.

        I would think you would need a welder, chop saw, 4 1/2" angle grinder, assorted hand tools (hammer, chisels, wrenches, ratches, sockets, etc), gloves, hood, soapstone, tape measure. That would be a bare minimum to do rudimentary work. I would then add an O/A setup, then air compressor (and air tools), then plasma cutter, then big steel fab table, bench grinder, 'nother welder (need a stick and a mig). There you have a basic shop, then you can shop for the big guns, ironworker, CAD plasma cutter, mill, lathe, sheet metal tools (brake, shear, bead roller, sliproll, etc)
        I am somewhere betwixt the two at the moment, and can do most anything, some things just take longer.

        Comment


        • #5
          Originally posted by FusionKing View Post
          I am confused......did you just post a question and then answer yourself???
          Uh.... that seems to be the case. move over, give me a little seat space on the bench.
          Will it weld? I loooove electricity!

          Miller 251/30A spool
          Syncro200
          Spectrum 625
          O/A
          Precix 5x10 CNC Router12"Z
          Standard modern lathe
          Cheap Chinese mill that does the trick... sort of...
          horizontal 7x12 bandsaw
          Roland XC540 PRO III
          54" laminator
          hammer and screwdriver (most used)
          little dog
          pooper scooper (2nd most used...)

          Comment


          • #6
            Ad Spam...!...??

            I think this is ad spam. Check the link at the bottom of his post....

            TacMig
            We depend On:
            Miller | Esab | Lincoln | Fronius
            Baileigh | Drake | Eagle | Knuth
            Victor | Harris | Smith | Bessey
            Snap-On | Hilti | Ingersoll Rand
            Burco/Koco | Onan | BobCat
            Tracker | Infratrol | AmeriCast

            We belong to or support:
            American National Standards Institute
            American Welding Society
            The Welding Institute
            Fabricators & Manufacturing Association Int'l.

            Anderson & Co. LLC
            Metal Cr
            afters

            Comment


            • #7
              Well I just needed some advise and found the article of startup equipment anyone could ad suggestions. I put the link of the article I found but meant no spam. Just need some advice.

              Thanks anyway

              Comment


              • #8
                and for big jobs with a whole lot of grinding i would add a 71/2 inch angle grinder, i got one real cheap at a tent sale for 25 bucks

                Comment


                • #9
                  Welcome...

                  Originally posted by El Guanche View Post
                  Well I just needed some advise and found the article of startup equipment anyone could ad suggestions. I put the link of the article I found but meant no spam. Just need some advice.

                  Thanks anyway
                  Didn't mean to offend you! It's that we have had spam here before and your original post along with your reply looked a little odd. In any event, good luck and happy welding.

                  TacMig
                  We depend On:
                  Miller | Esab | Lincoln | Fronius
                  Baileigh | Drake | Eagle | Knuth
                  Victor | Harris | Smith | Bessey
                  Snap-On | Hilti | Ingersoll Rand
                  Burco/Koco | Onan | BobCat
                  Tracker | Infratrol | AmeriCast

                  We belong to or support:
                  American National Standards Institute
                  American Welding Society
                  The Welding Institute
                  Fabricators & Manufacturing Association Int'l.

                  Anderson & Co. LLC
                  Metal Cr
                  afters

                  Comment


                  • #10
                    a good chop saw is a necessity. A grinder- you can get by with a 4 1/2" grinder but make sure you get a good one because if not you will replace them on a regular basis. torch setup.

                    Comment

                    Working...
                    X