Announcement

Collapse
No announcement yet.

What amperage range w/ thumb control

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • What amperage range w/ thumb control

    I am considering buying a thumb controller for my tig. Finding a place to get a pedal setup is a real pain in some positions. My question is how much current range will I lose. The unit costs about $175 and I thought I would get some opinions good or bad before buying. How difficult is it to get used to using ?Thanks so much, Adam
    Last edited by Jetmekdc-10; 07-07-2007, 10:53 AM. Reason: misspelled word
    Webb's Welding and Repair LLC
    MM210 w/a 3035 spoolgun
    Syncrowave 250
    Spectrum 625
    Trialbazer 302 w/HF
    http://webbsweldingandrepair.com/home

  • #2
    you wont loose any curent its still goint to alow you to ajust the same as a foot controle just les movement per increase/decrease. as for how hard ?? personal thing realy, some love them some hate them. there are several styels to chose from so pick one you think will be the easyest for your comfort.
    thanks for the help
    ......or..........
    hope i helped
    sigpic
    feel free to shoot me an e-mail direct i have time to chat. james@newyorkmetalart.com
    summer is here, plant a tree. if you don't have space or time to plant one sponsor some one else to plant one for you. a tree is an investment in our planet, help it out.
    JAMES

    Comment


    • #3
      CK has some nice ones, personally for out of position I rather just use a momentary button, set the amperage and toggle it off and on, or setup the slope feature on the Dynasty.
      Regards, George

      Hobart Handler 210 w/DP3035 - Great 240V small Mig
      Hobart Handler 140 - Great 120V Mig
      Hobart Handler EZ125 - IMO the best 120V Flux Core only machine

      Miller Dynasty 200DX with cooler of my design, works for me
      Miller Spectrum 375 - Nice Cutter

      Comment


      • #4
        dose the 250 Tigrunner have a slope option?? i still havent tryed that out on mine yet. but i figure i better get a lil more time in befor i start the fancy stuff.
        thanks for the help
        ......or..........
        hope i helped
        sigpic
        feel free to shoot me an e-mail direct i have time to chat. james@newyorkmetalart.com
        summer is here, plant a tree. if you don't have space or time to plant one sponsor some one else to plant one for you. a tree is an investment in our planet, help it out.
        JAMES

        Comment


        • #5
          The 250 does have the option to add on a pulse and sequencer panel. You can buy them for just under $500 and just plug them in. I was planning to get the panels when my skills and knowledge were at that point. The on/off switch may be the way to go. Thanks for the input. Adam
          Webb's Welding and Repair LLC
          MM210 w/a 3035 spoolgun
          Syncrowave 250
          Spectrum 625
          Trialbazer 302 w/HF
          http://webbsweldingandrepair.com/home

          Comment


          • #6
            Originally posted by fun4now View Post
            dose the 250 Tigrunner have a slope option?? i still havent tryed that out on mine yet. but i figure i better get a lil more time in befor i start the fancy stuff.
            The slope function on the T/A is really strightforward, I think you are ready to give it a try ... all you need is a momentary button, some wire, and the right amphonal connector for the T/A.
            Regards, George

            Hobart Handler 210 w/DP3035 - Great 240V small Mig
            Hobart Handler 140 - Great 120V Mig
            Hobart Handler EZ125 - IMO the best 120V Flux Core only machine

            Miller Dynasty 200DX with cooler of my design, works for me
            Miller Spectrum 375 - Nice Cutter

            Comment


            • #7
              i stumbled onto it once with my foot controle, so i may be able to use the foot controle as the triger to lern it. i was realy confused when i set it up for it (unknowingly by mistake) and tryed to weld like normal.LOL

              so even though the foot controle wont give me the convieneance of a small momentart swich i think i can use it for practise, till i get a swich.
              thanks for the help
              ......or..........
              hope i helped
              sigpic
              feel free to shoot me an e-mail direct i have time to chat. james@newyorkmetalart.com
              summer is here, plant a tree. if you don't have space or time to plant one sponsor some one else to plant one for you. a tree is an investment in our planet, help it out.
              JAMES

              Comment


              • #8
                all a pedal is to me is just an arc starter. i do alot of out of position so, i have about 4 diferent ways i hold the torch. this might be something to take into consideration.

                Comment


                • #9
                  Remote controls - several flavors

                  Originally posted by Jetmekdc-10 View Post
                  I am considering buying a thumb controller for my tig. Finding a place to get a pedal setup is a real pain in some positions. My question is how much current range will I lose. The unit costs about $175 and I thought I would get some opinions good or bad before buying. How difficult is it to get used to using ?Thanks so much, Adam
                  When welding out of position, a finger actuated remote control is a God-send. There seem to be several flavors available depending on your needs. Here's what I've found, from most basic to finest control.

                  1. On/Off button. Instant on. Instant off. Example: Miller RMS-14. (Most likely used with programmable slopes, or low amperage settings.)

                  2. On/Off/Momentary toggle. 3 position. Center position is off. Press one side to give monentary power. Press the other side to lock-on. Example: Miller RMLS-14. Use the Momentary setting for tacking. Use the ON position for the finish weld.

                  3. Finger wheel. Roll-on power. Ramps-up quickly. Roll-off power. Ramps-down quickly. Example: Miller RCCS-14. Good for production work.

                  4. Finger wheel. Roll-on power. Ramps-up slowly. Roll-off power. Ramps-down slowly. Example: Miller RCCS-14. More precise control, for surgery, or welding a long seam.

                  Here's a link to some of them.
                  http://www.millerwelds.com/products/...ccessories.php

                  There are other non-Miller makes of similar remote controls. Just make sure they are compatible with your TIG rig before purchasing.

                  I'm not sure why the are so pricey. They are basically switches at the end of some wire. However, as soon as you are talking about TIG gear, the price just seems to triple.
                  Dynasty 200 DX
                  Coolmate 3

                  Comment


                  • #10
                    my cuz has onefor his snyco wave it is kinda hard to get useto it ,personally I like the foot control better
                    just my $0.2 worth

                    Inferno Forge

                    Chris

                    Comment


                    • #11
                      i think they will all be a bit frustraiting to get used to at first but there is no question they will be verry usefull once masterd.
                      this one looks like the best choice IMO and the one i will be getting at some point if i chose to get one. right now i dont do anywhere near enough TIG, much less out of position to worry about it. arc-zone caries them and i think CK makes one built into the torch, or maybee its some one else but here is a link to the arc-zone one. they are great people to deal with( IME ).
                      http://www.arc-zone.com/catalog/web_...6892375_530993

                      here's a pic for quick reference.
                      Attached Files
                      thanks for the help
                      ......or..........
                      hope i helped
                      sigpic
                      feel free to shoot me an e-mail direct i have time to chat. james@newyorkmetalart.com
                      summer is here, plant a tree. if you don't have space or time to plant one sponsor some one else to plant one for you. a tree is an investment in our planet, help it out.
                      JAMES

                      Comment


                      • #12
                        I have a lightly used one set up for a DX300 (14 pin) for sale if you want a used one. It came from Arc-Zone and has about 50 hours use. It is just like the one pictured above.

                        Comment


                        • #13
                          cool how much $$ you looking to get out of it???
                          thanks for the help
                          ......or..........
                          hope i helped
                          sigpic
                          feel free to shoot me an e-mail direct i have time to chat. james@newyorkmetalart.com
                          summer is here, plant a tree. if you don't have space or time to plant one sponsor some one else to plant one for you. a tree is an investment in our planet, help it out.
                          JAMES

                          Comment


                          • #14
                            $145 + shipping
                            One of the velcro straps has a melted place where it was laid down on a hot piece. The unit is only about two months old and still under warranty. Still have the box for it. PM me if you want it

                            Comment

                            Working...
                            X