Announcement

Collapse
No announcement yet.

Plasma screen stands

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • #31
    Or you're more than 10' away.

    I was just curious. There's nothing wrong with leaving the edge there.
    Syncrowave 250DX
    Invison 354MP
    XR Control and 30A

    Airco MED20 feeder
    Thermal Dynamics Cutmaster 81
    Smith O/A rig
    And more machinery than you can shake a 7018 rod at

    Comment


    • #32
      That's what I keep telling myself.

      I wish I would have done the rings in one piece so the seam would have been in the back. I buffed them out pretty darn well, but... well, you know.

      I gotta let it go, though, and move on. They're going in a HUGE room and there will be these HUGE screens on them, so nobody will be looking at the bases anyways. As you know, when something's in your shop, you put it under the microscope.

      Thanks for the replies.

      The next jobs will be a bit more creative. Looks like some stainless, teak, and glass.
      Maxstar 200DX
      Maxstar 300DX
      Dynasty 200DX
      Passport
      Spectrum 701
      LMSW-52 spot welder

      Comment


      • #33
        I wasn't talking about the vertical seams, I was wondering about the horizontal one where the plate meets the "skirt."

        I did a wheel replacement stand for a guys show car where I made the mistake of cutting and welding a piece of flat stock rather than just getting a piece of plate and cutting it out as one unit. The time it took to hide the seam was more than it would've cost for the plate over the bar stock. He ended up mudding that to blend where the weld was (surface texture was off between the HRS and where I ground it), so I was wondering if your final presentation would also have that seam eliminated. That's all...

        He ordered up another one for a buddy and I already have the plate for that one. Live and learn.
        Syncrowave 250DX
        Invison 354MP
        XR Control and 30A

        Airco MED20 feeder
        Thermal Dynamics Cutmaster 81
        Smith O/A rig
        And more machinery than you can shake a 7018 rod at

        Comment


        • #34
          Job look good man, the kicker being we all seem to think of a better way to do things after we've done them.

          Fire your designer for that one though for the simple fact that I think he should have had you make the skirt about an 1" shy of the ground, so the end user could adjust the levelers as it sits. But then again it could be perspective.
          MILLER 180 W SPOOL GUN
          MIller CP 300 w/S22-A Feeder
          Miller Syncro 200
          Miller 375 X Plasma
          Miller Elite Hood
          JD2 Bender
          Tube Notcher
          Horizontal/ Verticle Bandsaw
          Makita Angle Grinders
          Arsenal of handtools
          Evolution Raptor dry saw
          Single Stage 60 Gallon Compressor
          Delta Drill Press

          "No fear to learn by doing", and a degree in Redneck Engineering

          Comment


          • #35
            Originally posted by SinGear View Post
            Fire your designer for that one though for the simple fact that I think he should have had you make the skirt about an 1" shy of the ground, so the end user could adjust the levelers as it sits. But then again it could be perspective.
            That's just the beginning with "designers." I'm tired of fighting the fight, so I just let them work it out. They always want things to "float" with no visible hardware. Magic. The installers will have a blast with this one. This is one of the reasons I don't do installations much anymore.

            It gets real fun when they all want things to be on locking casters, but they don't want the castors to be visible (e.g. accessible).

            Thanks for looking.
            Last edited by chrisgay@sbcglo; 09-17-2008, 09:09 AM. Reason: clarity
            Maxstar 200DX
            Maxstar 300DX
            Dynasty 200DX
            Passport
            Spectrum 701
            LMSW-52 spot welder

            Comment


            • #36
              Oh I hear ya on that one, I'm an Millwork engineer by trade and we deal with that BS all the time.

              Let me tell you what you need then you can suggest what you want
              MILLER 180 W SPOOL GUN
              MIller CP 300 w/S22-A Feeder
              Miller Syncro 200
              Miller 375 X Plasma
              Miller Elite Hood
              JD2 Bender
              Tube Notcher
              Horizontal/ Verticle Bandsaw
              Makita Angle Grinders
              Arsenal of handtools
              Evolution Raptor dry saw
              Single Stage 60 Gallon Compressor
              Delta Drill Press

              "No fear to learn by doing", and a degree in Redneck Engineering

              Comment


              • #37
                Originally posted by SinGear View Post
                Job look good man, the kicker being we all seem to think of a better way to do things after we've done them.
                It's how man has improved on everything he's ever built. It's ended up with the International Space Station and rovers on Mars. Is that cool or what??

                Chris:
                Thanks for sharing your agitation with your 'misconceptions'. I'm just a hobby guy, if I need a widget, I build it. First I 'engineer the cwap out of it'. Then, when I step back to look at the finished project; I wonder what the h*ll I was thinking. Everything in my world is a protype; room for improvement. But I only needed ONE.

                It's nice to know, that even the 'shop guys', aren't perfect in 'their own eyes'.

                Thanks for the pics, triggers the imagination.

                Craig
                RETIRED desk jockey.

                Hobby weldor with a little training.

                Craftsman O/A---Flat, Vert, Ovhd, Horz.

                Miller Syncrowave 250.
                sigpic

                Comment


                • #38
                  Glad it's over

                  Making these things was an OK job, but I'm really glad they're out of my chop and I can move on to something with some more style.

                  Next up is a stainless and teak gate, a glass windscreen, and a corten privacy screen. This one will be all my own design, so I get call it how I see it.

                  Gotta eat.
                  Attached Files
                  Maxstar 200DX
                  Maxstar 300DX
                  Dynasty 200DX
                  Passport
                  Spectrum 701
                  LMSW-52 spot welder

                  Comment


                  • #39
                    Chris - Great job. Looks factory made. BTW - any idea what one weighs? Your work has given me some ideas for a museum display.

                    Thanks.

                    Comment

                    Working...
                    X