Announcement

Collapse
No announcement yet.

Miller Trailblazer Custom Trailer

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    Thanks guys for you great comments and I'm happy to know you folks like what I've done here. I've been receiving a few emails asking how I did the sliding rear drawer so I attached a few pictures of it for you to see. The sliding drawer works off two heavy duty ball bearing tracks. Much the same as you would see on a high end tool box. It works very smooth and is very strong. Have a look. Thanks
    Attached Files
    Miller matic 350P
    Millermatic 252/Spool gun
    Miller Spectrum 875 plasma
    Miller Dynasty 200 DX
    Miller Coolmate 3
    Miller Elite ( INFERNO Digital)
    2008 Miller Trailblazer 302/Custom trailer
    Custom DX200 Crazy Cart
    Sofia 13 X 30 Lathe
    MODERN 10X50 knee mill with Fagor 40i DRO
    Craftex 30 Mill/Drill

    All this stuff below was done with Miller gear


    My YouTube vids:

    http://www.youtube.com/user/7863348

    Flickr photo's:
    http://www.flickr.com/photos/15602393@N05/sets/

    Comment


    • #17
      I too did a fancy cart fot my Dynasty 300 DX, painted it blue with 4 hooks for the cables, shelf on the top, crane hook and 8 spots for my rod tubes.

      I thought mine was over kill untill I saw yours, nice job.

      As far as trailers I did one for an old Miller big 40 years ago with the miller stickers, but I diddnt see any tanks mounts on your trailer.

      However very nice job, you need to rent yours out to the miller road show guys.

      Comment


      • #18
        Thanks Portable. Sounds like you have some nice welding gear there. As for the tanks or the lack of them on my trailer. If you look at picture T5 you'll see there's a place there for tanks or a new Miller Plazma. I mentioed this in my opening write up but I'm only now getting around to doing that this week and I'm leaning towards the new plazma to place there. Anyone have any advise on what "Miller" plazma I should go with that would work well with the new Trailerblazer? As always you comments and suggestions are always appreciated.
        Miller matic 350P
        Millermatic 252/Spool gun
        Miller Spectrum 875 plasma
        Miller Dynasty 200 DX
        Miller Coolmate 3
        Miller Elite ( INFERNO Digital)
        2008 Miller Trailblazer 302/Custom trailer
        Custom DX200 Crazy Cart
        Sofia 13 X 30 Lathe
        MODERN 10X50 knee mill with Fagor 40i DRO
        Craftex 30 Mill/Drill

        All this stuff below was done with Miller gear


        My YouTube vids:

        http://www.youtube.com/user/7863348

        Flickr photo's:
        http://www.flickr.com/photos/15602393@N05/sets/

        Comment


        • #19
          Looks great

          That is a very nice looking trailer. I like the cart too.
          67vw

          (o\_|_/o)

          Comment


          • #20
            awesome job! you must have a good amount of time just planning that thing
            my daddy always said i was IRONHEADED....
            feel free to P/M me

            Comment


            • #21
              Can't really add anything, excellant job. I too think people do better work when they have nice equipment. Not always, but to me indicates they care about what they do
              Scott
              HMW [Heavy Metal welding]

              Comment


              • #22
                Originally posted by wildfire View Post
                Anyone have any advise on what "Miller" plazma I should go with that would work well with the new Trailerblazer? As always you comments and suggestions are always appreciated.
                Looks like the Spectrum 625 is a good match

                Ed Conley
                http://www.screamingbroccoli.net/
                MM252
                MM211
                Passport Plus w/Spool Gun
                TA185
                Miller 125c Plasma 120v
                O/A set
                SO 2020 Bender
                You can call me Bacchus

                Comment


                • #23
                  Very nice and professionally done!

                  Comment


                  • #24
                    Great job. i love all the kinda hidden storage areas

                    Comment


                    • #25
                      Thanks guys for your comments. I realized shortly after I built the trailer that although I like where I placed the rear lights it created a problem. I built and installed the roll bars and put my company logo on it and people would want to get so close to the rear of the trailer to view it I was afraid I would get rear ended so I installed a LED light bar up on the roll bar to try and prevent that from happening. I installed a picture and a video of how it works. Thanks again


                      http://www.youtube.com/watch?v=5xl6t6_UNpA
                      Attached Files
                      Miller matic 350P
                      Millermatic 252/Spool gun
                      Miller Spectrum 875 plasma
                      Miller Dynasty 200 DX
                      Miller Coolmate 3
                      Miller Elite ( INFERNO Digital)
                      2008 Miller Trailblazer 302/Custom trailer
                      Custom DX200 Crazy Cart
                      Sofia 13 X 30 Lathe
                      MODERN 10X50 knee mill with Fagor 40i DRO
                      Craftex 30 Mill/Drill

                      All this stuff below was done with Miller gear


                      My YouTube vids:

                      http://www.youtube.com/user/7863348

                      Flickr photo's:
                      http://www.flickr.com/photos/15602393@N05/sets/

                      Comment


                      • #26
                        LOL, Thats cool. Very creative
                        Scott
                        HMW [Heavy Metal welding]

                        Comment


                        • #27
                          wow, did you just do a wax job on that tb 302?

                          Comment


                          • #28
                            wildfire, had to add my EXCELLENT job in there!!! Lights work REALLY REALLY nice, but with all the lights off, I'd put a couple of large reflectors on the diamond plate for added insurance....
                            great job dude!!!!!!!!
                            I'm not late...
                            I'm just on Hawaiian Time

                            Comment


                            • #29
                              If your going for show the plazma cutter is pretty cool but if your going to actually work it then I would put torches on because of the wide range of stuff the torched do.

                              You could put a plazma that has an on board compressor but they dont cut really thick stuff compared to what torches will do.

                              If you already have a compressor on your truck to run say the 2050 plazma then your ok.

                              Comment


                              • #30
                                Thanks guys for your advice and comments. I took the rig out to a local RV park the other day to do some welding for a customer and the thing actually drew a crowd. folks taking pictures and asking lots of question. One guy said he's going to get me to build him a custom trailer. Funny how things happen :laugh:

                                Anyway the other day our steel supplier dropped by with a sheet of 4X8 1/4 plate. Man you should have seen the wife trying to get that off the truck Anyway I decided to look for an old used forklift and I found one. Don't laugh, I didn't pay much for it. runs like a clock but I got some work to do on it before I'm happy with it. I think I may put a custom spin on the thing :blob2:
                                Attached Files
                                Miller matic 350P
                                Millermatic 252/Spool gun
                                Miller Spectrum 875 plasma
                                Miller Dynasty 200 DX
                                Miller Coolmate 3
                                Miller Elite ( INFERNO Digital)
                                2008 Miller Trailblazer 302/Custom trailer
                                Custom DX200 Crazy Cart
                                Sofia 13 X 30 Lathe
                                MODERN 10X50 knee mill with Fagor 40i DRO
                                Craftex 30 Mill/Drill

                                All this stuff below was done with Miller gear


                                My YouTube vids:

                                http://www.youtube.com/user/7863348

                                Flickr photo's:
                                http://www.flickr.com/photos/15602393@N05/sets/

                                Comment

                                Working...
                                X