Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums

  • If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Announcement

Announcement Module
Collapse
No announcement yet.

Dune Buggy

Page Title Module
Move Remove Collapse
X
Conversation Detail Module
Collapse
  • Filter
  • Time
  • Show
Clear All
new posts

  • Dune Buggy

    so my friend wanted to build a dune buggy but has no fabrication skills at all so i told him i'd help him out and show him everything i know on the subject as we build it. Got the 1 5/8" .120 wall DOM tubing on friday along with the 1 1/2 .250 wall DOM for the 4 link and the control arms. Were using a Trick Tools model 3 bender which i am quite impressed with. drivetrain is a chevy 350/350 and a 10 bolt rearend (will upgrade when it breaks)

    the only thing i dont like about how its turning out is the rear main hoop, it looks too wide.
    but anyways let me know what you think. BTW: there will be alot more triangulation, the top rails are just sitting there right now.
    Attached Files

  • #2
    looks like fun what are you use for front suspension? you fab your own or use straight axle? we are going to build one next year i think useing and s-10 rear and doing mods. to the frame and build a cage with 305/350th

    Comment


    • #3
      we have s10 spindles and brakes and balljoints so im going to build the arms for the front. He has an s10 rearend too but its pretty narrow, so i traded him my 8.5" out of the camaro since im not going to use it and its got a limited slip.

      Comment


      • #4
        equipment

        Looks like you got the equipment to build this thing..Good luck on your project!
        Farris

        Comment


        • #5
          Thanks Farris.

          Got a little bit more work done today, lemme know what you think.
          BTW the metal isnt rusted, thats just the residu from the oils or something
          Attached Files

          Comment


          • #6
            what does something like this sell for in your area?
            Bobby

            Comment


            • #7
              Honestly not sure what they go for around here but front engined v8 rails go for 10k w/o motor/tranny on the internet.

              Comment


              • #8
                got the lowers done this afternoon, starting to come together. let me know what you think
                Attached Files

                Comment


                • #9
                  That thing looks sweet. You guys are really moving along on it huh! Keep us posted!

                  Comment


                  • #10
                    Nice job! Looks like have have plenty of travel. What kind of spring are you going to use? Coil overs?

                    Comment


                    • #11
                      welder

                      Zach, Yes it is looking better all the time. Zach, what size is your welder and what size wire you using? I was wondering if you might show us a picture of some of your welds closer up?
                      Thanks!

                      Comment


                      • #12
                        Thanks guys

                        Im going to be building my own coilovers for the time being since good offroad ones are pretty expensive. For the front ill be using a pair of springs i grabbed from the junkyard and the rear will be using the origional front springs from my camaro. Also the rear will have a "cantilever" which will give me the mechanical advantage i need over the spring to lower the spring rate as well as giving me the 14" of travel needed.

                        For the chassis im using my MM251 right now its setup with .030 wire, but i alternate between that and .035 I dont have any pics of the welds on the chassis yet since its still tacked together but when i weld it up ill post some closeup pics. For the suspension pieces ill be using my syncrowave 180

                        thanks again,
                        Zach

                        Comment


                        • #13
                          Started tig welding the control arms today, got one bead into them and ran out of argon. go figure...

                          So then i built the motor mounts and transmission mount/crossmember. owner wanted the crossmember to be welded not bolted. oh well he will figure out why it should be bolted when he has to change a tranny haha.
                          Attached Files

                          Comment


                          • #14
                            Lookin good Zach, yeah he'll have tight jaws if a tranny change is due.LMAO
                            Thanks for sharin the proj. pics.
                            L*S

                            BTW, can I come over and play, can I, can I, huh?LOL

                            Comment


                            • #15
                              haha Leons, your welcome to stop by anytime.

                              Welded all the 4 link bars and the bushing ends of the a arms tonight. If you see anything in the welds that should be changed im open to suggestions. i was using 3/32 %2 T, 3/32 er 70-6? maybe Filler and about 120 amps
                              thanks
                              zach
                              Attached Files

                              Comment

                              Working...
                              X
                              Special Offers: See the latest Miller deals and promotions.