Announcement

Collapse
No announcement yet.

MIG trigger is too sensitive for me

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • MIG trigger is too sensitive for me

    The MIG trigger is too sensitive for me. With gloves on i can actuate the trigger when setting up a weld start point or moving to q new location. This retults in a blast of wire making contact with thing I do not want to weld. Is there a way to increase the pressure required to actuate the trigger?
    Thanks all Skip

  • #2
    if we knew what type of rig you have, we may come up with a solution, welcome to the forum

    Comment


    • #3
      Welcome to the forum Skip.
      Lincoln A/C 225
      Everlast PA200

      Comment


      • #4
        Originally posted by kevin View Post
        if we knew what type of rig you have, we may come up with a solution, welcome to the forum
        That might help a bunch, but one possible way would be to install a stiffer spring behind the trigger.

        Comment


        • #5
          A fix

          Take the handle apart and spread the contacts out with some needle nose. That's how we get a lite trigger pull by bending them closer together . Should fix your problem.
          Jason

          Comment


          • #6
            How can we give you any useful advice if you have not given us the make and model of MIG gun??

            They are all different... some have microswitches.. some have flat brass springs... others yet again different... useless to try and guess till you give us more info..

            MAKE?? MODEL??
            Last edited by H80N; 04-09-2014, 07:49 PM.
            .

            *******************************************
            The more you know, The better you know, How little you know

            “The bitterness of poor quality remains long after the sweetness of low price is forgotten”

            Buy the best tools you can afford.. Learn to use them to the best of your ability.. and take care of them...

            My Blue Stuff:
            Dynasty 350DX Tigrunner
            Dynasty 200DX
            Millermatic 350P w/25ft Alumapro & 30A
            Millermatic 200

            TONS of Non-Blue Equip, plus CNC Mill, Lathes & a Plasmacam w/ PowerMax-1000

            Comment


            • #7
              Keep your finger off the trigger when you're not welding, hope to **** for the safety of anyone around you you don't own a handgun.
              Miller Trailblazer's ( 2 )...MillerBobcat 250...Millermatic 251's ( 2 )...Miller Syncrowave 200...Miller Syncrowave 180SD...Miller 12VS Suitcases ( 2 )... Hobart Hefty CC/CV Suitcases ( 2 )...Miller 30A Spool Guns ( 2 )...Miller WC 15A Control boxes ( 2 )...Thermo Dynamics Cutmaster 50 Plasma Cutters ( 2 )...Thermo Arc Hi Freq Units ( 2 )...Smith / Victor O/A Sets...DeWalt Power Tools...Craftsman / Snap On Hand Tools... Two Dodge Mobile Rigs

              Comment


              • #8
                it may be too sensitive or...maybe you are using extra heavy stiff gloves?

                without the model as other said we can feed you infinitely with various suggestions

                Comment


                • #9
                  since we dont know what you have, we could assume that you have one of them 99 buck specials at h f , where the wire is always hot, it is not one of them, i hope

                  Comment


                  • #10
                    Wear thinner gloves. Those heavy stick arc gloves give you no feel. Look at the tillman mig gloves or something similar.. If you are using a miller mig gum, you can disassemble the red switch, and there is a spring in there. You can pull it apart slightly, but in all the triggers I have had, i have never had a spring issue. Try another similar gun at the LWS to see if it is a lot different than yours, if so, then order a new one. Sometimes dirt will get inside the switch, not allowing it to fully open, might look into that.

                    Comment


                    • #11
                      I occasionally have the same problem with the original offering GA-20 gun on my MM200.

                      Easiest fix is to condition yourself to hold your trigger finger straight out along the side of the gun instead of leaving it hovering over the trigger when repositioning.
                      MM200 w/spot controller and Spoolmatic 1
                      Syncrowave 180 SD
                      Bobcat 225G Plus LPG/NG w/14-pin*
                      *Homemade Suitcase Wire Feeder
                      *HF-251D-1
                      *WC-1S & Spoolmatic 1
                      PakMaster 100XL
                      Marquette "Star Jet" 21-110
                      http://www.millerwelds.com/images/sm...rolleyes.png?2

                      Comment

                      Working...
                      X