Announcement

Collapse
No announcement yet.

Lets see pictures of your band saws

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    Originally posted by Synchroman View Post
    I have a 1987 Enco 7X12 Horizontal/Vertical Bandsaw. It was built in Taiwan. It originally had a large coolant tank in the bottom of the chassis but it made a mess so I modified the saw. I changed it to a dry sump and used the original pump to raise the coolant up to the blade from a two gallon tank. I added a catch tray and raised the unit up on risers for easy cleaning. The coolant drains back down to the tank through a filter. I use Mobil soluble oil and the blades last a long time.

    I welded the tank myself using 1/8" steel plate. The unit works quite well and will do a very straight, even cut.


    The unit.





    The coolant tank.

    Nice saw and improvements Synchroman. Taiwan machinery isn't bad, I have Rong Fu Mill I like very much.

    Can you show pics of your portable hydraulic unit? It looks good.

    Comment


    • #17
      Originally posted by tackit View Post
      Nice saw and improvements Synchroman. Taiwan machinery isn't bad, I have Rong Fu Mill I like very much.

      Can you show pics of your portable hydraulic unit? It looks good.
      If you are referring to the unit next to the saw on the left, that's a vintage Bernard TIG cooler. I have two coolers. One is the Bernard (2.5 gallon), and the other is a homemade cooler that holds 10 gallons. Both have Procon pumps and special motors to drive the pumps. I alternate then now and then just for fun.

      Here they are side by side a few years ago after I rebuilt the Bernard. I also welded up the carts that they are sitting on using old bed frames. If only those bed frames could talk. LOL.

      Rong Fu is a good name in equipment. I had a R.F. Mill Drill for more than ten years before I got a large Webb (Bridgeport clone).

      http://i144.photobucket.com/albums/r...ps4a91f322.jpg
      Last edited by Synchroman; 09-11-2013, 09:19 AM.
      Miller Syncrowave 200
      Milermatic 252
      Lincoln AC/DC "Tombstone"

      Comment


      • #18
        You do nice work synchroman. I was thinking how uncluttered your hydraulic unit looked. That's a nice Web mill you have too.

        Comment


        • #19
          Originally posted by tackit View Post
          You do nice work synchroman. I was thinking how uncluttered your hydraulic unit looked. That's a nice Web mill you have too.
          Well thank you very much for the nice compliment! I'm a hobby welder and machinist so I probably have more time for "G" jobs than most. I sure enjoy this work, however. I've always admired professional welders, too.

          Miller Syncrowave 200
          Milermatic 252
          Lincoln AC/DC "Tombstone"

          Comment


          • #20
            Anybody else using an old-fashioned power hacksaw? SLOW, but always nice straight cuts.

            Comment


            • #21
              What do you do most often in your band saws? Typical work you do?

              Comment


              • #22
                Originally posted by old jupiter View Post
                Anybody else using an old-fashioned power hacksaw? SLOW, but always nice straight cuts.
                Yup, I have three. A Racine and two others that were converted from line shaft drives to motor drives a long time ago. Also have a V-36 Doall band saw.---Meltedmetal

                Comment


                • #23
                  I got a picture of my band saw made by Rollin
                  Attached Files

                  Comment


                  • #24
                    JET J-3410 7-Inch by 12-Inch 3/4-Horsepower 115-Volt Single Phase Horizontal Wet Bandsaw

                    Click image for larger version

Name:	photo.jpg
Views:	1
Size:	49.0 KB
ID:	516055
                    Lincoln Vantage 400
                    Trailblazer® 302 Air Pak™

                    Miller Dynasty® 350
                    Millermatic 350P Aluminum
                    Millermatic® 252
                    Syncrowave 351
                    Lincoln LN-25 Pro

                    Multimatic™ 200

                    XR-Aluma Pro Gun
                    Diversion™ 180

                    Spectrum® 625 X-TREME™

                    Thermal Dynamics® Cutmaster® 52
                    Victor Oxy/Acetylene Set

                    Comment


                    • #25
                      Nice saws. I've have always wanted a reciprocating saw, my old dear friend who patiently taught me how to weld after I got out of weld school has had one for ages, he never talks about getting a band saw.


                      He's built so many trailers out of every kind of formed metal he could get his hands on I can only guess the number. He used to pick up old overhead garage door tracks from garage door businesses, he would double them up to make carts, trailer frames and just about anything he wanted from them. Reminiscing here a bit.....I love you Joe.

                      Comment

                      Working...
                      X