hey everyone! i'm new to this forum and i was having trouble and heard of this site on a tv show. My problem is I have rusty pipe and a galvanized cattle panel and i'm making a cattle pen out of it. I am having trouble with the vertical part. everything else goes in awesome but I am doing something wrong on the vertical part. the pipe thickness is schedule 10 so its easy to burn through which is my main problem. The welder i have is a bobcat 250. Thanks in advance for any opions. I'll post pictures tommorow so it will make more sense. Wondering what rod you would use and what amperage i would set it on?
Announcement
Collapse
No announcement yet.
Having trouble welding galvanized to rusty pipe
Collapse
X

I like 3/32 or 1/8 6010 DC . Actually, I thought that 6011 was the same as 6010 but for AC.
Check out the MILLER weld calculator.
http://www.millerwelds.com/resources...calculator.php
Comment

Unless I'm doing a root on pipe I always prefer 6011. and I agree with Weldon welding 3/32
Galvanize is a coating as well as rust so clean it up, gope the pipe to minimize the gap.
You also may want to use a method where you weld for a second, let it cool a second and restrike the arc and keep doing this untill your gap gets closer.
You might also want to do a weave then stop for 5 seconds and let it cool then do another while you stack them on one another forming a wide weld bead.
Good luck.
Comment

As long as it wasn't a structural weld when I had gaps to big to fill I would cut or find a piece of steel that would fill the gap and weld over it, making it part of the weld.
Or run the sides down hand jumping from side to side so the weld would cool on one side as we welded the other. we called it spiderwebbing.Last edited by tackit; 04052013, 06:52 AM.
Comment

Originally posted by Darrren Bartlett View Postthanks everyone for the help! only question i have left is on my machine for the amps it just has one through 10. What does 50 mean? how do i figure it out? Am i missing something on the machine? below is what my machine looks like. thanks again!
http://www.millerwelds.com/om/o249336b_mil.pdfEd Conley
http://www.screamingbroccoli.net/
MM252
MM211
Passport Plus w/Spool Gun
TA185
Miller 125c Plasma 120v
O/A set
SO 2020 Bender
You can call me Bacchus
Comment

Set the middle/ or course adjustment to 40/100 amps and use the 110 to get to the 50 amps or whatever you decide up to 100 amps.
Looks like each line represents 10 amps on the 110 scale in the 40/100 amp course range scale. So the knob set on 5 = 50 amps ...set on 10 = 100 amps .. the 110 scale is for fine tuning.
On my 200 aead legends if I remember correctly I had to keep the fine tuning knob set to it's highest setting when using it for a generator, also you're not suppose to change welding modes while welding.
Important to use the right size welding lead if you want full power at a distance.
Changed due to 140 amp scale was wrong, it's 40 /100 scaleLast edited by tackit; 04052013, 01:22 PM.
Comment

Scales would be as follows
40130A range (each step is 10 Amps)
1  40A
2  50A
3  60A
4  70A
5  80A
6  90A
7  100A
8  110A
9  120A
10  130A
60160A range (each step is 11.11 Amps)
1  60.0A
2  71.1A
3  82.2A
4  93.3A
5  104.4A
6  115.5A
7  126.6A
8  137.7A
9  148.8A
10 160.0A
80225A range (each step is 16.11 Amps)
1  80.0A
2  96.1A
3  112.2A
4  128.3A
5  144.4A
6  160.5A
7  176.6A
8  192.7A
9  208.8A
10  225.0A
100250A range (each step is 16.66 Amps)
1  100A
2  116.6A
3  133.3A
4  150.0A
5  166.6A
6  183.3A
7  200.0A
8  216.6A
9  233.3A
10 250.0A
Not having one in front of me this would only be the case if the knob only goes down to 1 and stops and up to 10 and stops. If it goes below 1 like to a 0 value or higher than 10, then I would need to recalculate the steps.Last edited by clint738; 04052013, 12:26 PM.
Comment

Originally posted by Darrren Bartlett View Postthanks everyone for the help! only question i have left is on my machine for the amps it just has one through 10. What does 50 mean? how do i figure it out? Am i missing something on the machine? below is what my machine looks like. thanks again!
So if you set the middle knob at 100250 amps, that gives you a 150 amp range. each number would be 10% of that range starting at 100.
If you set it to 40100 then the range would be 60.Last edited by MMW; 04052013, 07:39 PM.MM250
Trailblazer 250g
22a feeder
Lincoln ac/dc 225
Victor O/A
MM200 black face
Whitney 30 ton hydraulic punch
Lown 1/8x 36" power roller
Arco rotophase model M
Vectrax 7x12 band saw
Miller spectrum 875
30a spoolgun w/wc24
Syncrowave 250
RCCS14
Comment
Comment