Announcement

Collapse
No announcement yet.

Service Manual Dynasty 350

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    Originally posted by cruizer View Post
    I appear to be the only one with that info, but it won't help you.

    Only 2 checks to make

    RC1 check for 325Volts bewteen RC1-1 to RC1-3, unit on at idle

    RC2 check for +15 volts between RC2-1 to RC2-2 HF off
    Check for 0 volts HF on

    Or 700HZ betwwen RC2-1 and RC2-2 HF on

    If that is there, all is happy and you need a new PC-7 Replacing parts on this board is probably NOT a good thing. as it may dynamite the rest of the machine.

    cruizer - Thank you for responding!

    I will check those voltages this weekend (hopefully). Right now I'm out of town for work. Please confirm with welder on and set to HF start mode:
    RC1-1 to RC1-3 voltage at idle is 325V AC or DC?
    RC2-1 to RC2-2 should +15 VDC pedal up?
    RC2-1 to RC2-2 should 0 VDC pedal down?


    I don't have a scope right so I can't check the 700Hz now but I can buy a scope if need be. I'd rather invest the $500 in a scope and fix the card for $15... but I will take your advice as we work through this. Thanks!

    Comment


    • #17
      Whoops, yes DC volts

      Comment


      • #18
        Just to rule this out.

        I had a 350DX delivered that would only work on lift arc. It turned out to have a Canadian board in it instead of the USA board. When the correct board was installed it worked perfectly.
        Nothing welded, Nothing gained

        Miller Dynasty700DX
        3 ea. Miller Dynasty350DX
        Miller Dynasty200DX
        ThermalArc 400 GTSW
        MillerMatic350P
        MillerMatic200 with spoolgun
        MKCobraMig260
        Lincoln SP-170T
        Linde UCC305 (sold 2011)
        Hypertherm 1250
        Hypertherm 800
        PlasmaCam CNC cutter
        Fadal Toolroom CNC Mill
        SiberHegner CNC Mill
        2 ea. Bridgeport
        LeBlond 15" Lathe
        Haberle 18" Cold Saw
        Doringer 14" Cold Saw
        6 foot x 12 foot Mojave granite

        Comment


        • #19
          Ummm, Canadain boards and US boards are the same.... CE (european) boards are different.

          Comment


          • #20
            Originally posted by cruizer View Post
            Ummm, Canadain boards and US boards are the same.... CE (european) boards are different.
            Perhaps that was what it was then. A call to Miller confirmed it though. The new board cured the start problem.
            Nothing welded, Nothing gained

            Miller Dynasty700DX
            3 ea. Miller Dynasty350DX
            Miller Dynasty200DX
            ThermalArc 400 GTSW
            MillerMatic350P
            MillerMatic200 with spoolgun
            MKCobraMig260
            Lincoln SP-170T
            Linde UCC305 (sold 2011)
            Hypertherm 1250
            Hypertherm 800
            PlasmaCam CNC cutter
            Fadal Toolroom CNC Mill
            SiberHegner CNC Mill
            2 ea. Bridgeport
            LeBlond 15" Lathe
            Haberle 18" Cold Saw
            Doringer 14" Cold Saw
            6 foot x 12 foot Mojave granite

            Comment


            • #21
              The CE model is PC7 . . 235 476 The US Model is . PC7 . . 233 144

              Comment


              • #22
                I was finally home enough time to check the welder as requested. The results are below:

                RC1-1 to RC1-3: 321VDC stable
                RC2-1 to RC2-2: 0 volts pedal up or down
                RC2-1 to RC2-2: Frequency is unstable when pedal is down and reads in the Mhz (most likely induced voltage from RF)

                During testing the HF worked intermittently and gave both a very strong and sharp crackle while other times giving about a half crackle, DC voltage never showed on the RC2-1 to RC2-2. I wore rubber linesman gloves and welding gloves and wiggled the RC2 and RC1 wires while depressing the pedal. That did not change my results.

                Cruizer... what do you think we should do now?
                Last edited by wumpscut223; 11-05-2013, 08:10 AM.

                Comment

                Working...
                X