Miller Electric

Welding Discussion Forums

Home » Resources » Communities » Welding Discussion Forums

  • If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Announcement

Announcement Module
Collapse
No announcement yet.

What is this welding equipment worth?

Page Title Module
Move Remove Collapse
X
Conversation Detail Module
Collapse
  • Filter
  • Time
  • Show
Clear All
new posts

  • What is this welding equipment worth?

    I have the following:

    Miller Dynasty DX (KJ171178)
    Miller Dynasty 300DX (KK115418)
    Miller Spectrum 2050 (KJ140832)

    Foot controls
    New TIG Torch
    Used TIG Torch
    2) Rod holders
    2) Grounding clamps
    2) 60 amp plugs
    2) 480v 60 amp quick disconnects with plug in
    1) 480v 60amp quick disconnect
    Stainless filler rods, about 100 lbs (1/8 & 3/16)
    Various fittings for the TIG Torches

    All of the equipment is from an industrial plant and has not been used since shutdown in 2007.

    In 2009 I brought the 300DX in for inspection and repair. (2 power modules replaced, $500)

    This equipment is overkill for my basic needs. I would like to sell it and get something more my speed (Just learning to weld, basic home and garage use)

  • #2
    If its something you already own a 200 dyn would be ideal and the 2050 fits right in, runs from common 50A single service. I wouldnt trade, spend, buy or sell if I had those if I didnt have to.

    Comment


    • #3
      Equipment value

      Value depend on the condition of the machines an the need of the buyer ;but nothing is over killing in welding more you have ,more you can do and better quality,as someone post allready i will also tell you not to sell if dont need or will regret later

      Comment


      • #4
        Originally posted by jg1171 View Post
        I have the following:

        Miller Dynasty DX (KJ171178)
        Miller Dynasty 300DX (KK115418)
        Miller Spectrum 2050 (KJ140832)

        Foot controls
        New TIG Torch
        Used TIG Torch
        2) Rod holders
        2) Grounding clamps
        2) 60 amp plugs
        2) 480v 60 amp quick disconnects with plug in
        1) 480v 60amp quick disconnect
        Stainless filler rods, about 100 lbs (1/8 & 3/16)
        Various fittings for the TIG Torches

        All of the equipment is from an industrial plant and has not been used since shutdown in 2007.

        In 2009 I brought the 300DX in for inspection and repair. (2 power modules replaced, $500)

        This equipment is overkill for my basic needs. I would like to sell it and get something more my speed (Just learning to weld, basic home and garage use)
        these are from 1998 and 1999 there is no point in going down to a 200 dx if u already own dynasty 300 your much better to stick with what u have plus u already know what u got it works and not costing u a dime just sitting there plus u will find u want to weld more then 1/4 inch u will be mad at your self sorry to yack at ya just my two cents

        Comment


        • #5
          simple ebay.

          If you dont know value use ebay list the exact name of each welder in the title . List serial numbers and pics in the describtions. Let the auctions run for 7 days.

          Comment


          • #6
            Originally posted by Tryagn5 View Post
            If you dont know value use ebay list the exact name of each welder in the title . List serial numbers and pics in the describtions. Let the auctions run for 7 days.
            i have seen them on ebay around 1500 or so for the 2050 and around 3000 to 3500 for the dynasty 300 but thats probably not what there worth cause if it was a deal it would not still be on ebay

            Comment

            Working...
            X
            Special Offers: See the latest Miller deals and promotions.