Announcement

Collapse
No announcement yet.

Weld Spatter Spray

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Weld Spatter Spray

    I hooked up my 211 yesterday for the first time and began running beads for practice. Most came out pretty good. I did notice a little fine spatter on a few of them; nothing horrible.

    I quickly figured out I needed welding pliers because my little ****s were not working out. While shopping online for some I noticed Welding Spatter Spray. Not just spray but also dip. Then I read about using Pam cooking spray.

    Please educate me on if I need to use it, when I need to use it, which type I should use, and how much to use. Is it only applied to the gun tip?

  • #2
    Hi Frank,

    I actually just did this last night for the first time - and was responsible for a recent 'anyone used PAM' recently thread too.

    I used a product from Airc(something) - it's anti-splatter spray - a little pump bottle of liquid. It actually was pretty nice in result - using flux core - I was getting a ton of splatter with my MM211. As a new hobbyist - last thing I need is splatter all over in addition to 'novice beads' - although - I'm pretty happy with what I've been laying down recently with my stick and new mig. I spray the metal joint and surrounding area and also was periodically spraying the nozzle probably every third bead (about 6" or so each). Running .030 flux on 110V btw - actually 1/4" metal - settings set manually to 3/16" metal - but I'm just getting to know my machine, some hood time and experimenting with drag vs. push techniques, positions etc. (so all - rest assured I know the settings aren't optimal for the thickness just working on some scrap!)

    I plan on using PAM next - this anti splatter product was about $12 or $13 bucks - PAM is what - about $3-5 in a grocery store.

    Hope this helps.
    John
    Miller Thunderbolt 225 AC/DC
    Millermatic 211 Auto/MVP

    Comment


    • #3
      I use splatter spray mainly on objects I can't have any splatter. If I'm welding close to a machined surface I'll spray it & cover it as best I can. Very rarely do I use it on the nozzle anymore but used to when I would run bigger wires at my old job. I've never used pam so can't comment on that. Personally I don't like nozzle dip, don't know why just don't use it.

      I use this stuff.


      http://www.gts-welco.com/gtsweldssto...l.aspx?ID=1455
      MM250
      Trailblazer 250g
      22a feeder
      Lincoln ac/dc 225
      Victor O/A
      MM200 black face
      Whitney 30 ton hydraulic punch
      Lown 1/8x 36" power roller
      Arco roto-phase model M
      Vectrax 7x12 band saw
      Miller spectrum 875
      30a spoolgun w/wc-24
      Syncrowave 250
      RCCS-14

      Comment


      • #4
        Pam, cheap & works as good as the dip/spray anti-splatter. With correct voltage setting using C25 splatter should be almost non-existant.
        Last edited by Old Skool; 12-10-2012, 12:49 PM.
        Miller Trailblazer's ( 2 )...MillerBobcat 250...Millermatic 251's ( 2 )...Miller Syncrowave 200...Miller Syncrowave 180SD...Miller 12VS Suitcases ( 2 )... Hobart Hefty CC/CV Suitcases ( 2 )...Miller 30A Spool Guns ( 2 )...Miller WC 15A Control boxes ( 2 )...Thermo Dynamics Cutmaster 50 Plasma Cutters ( 2 )...Thermo Arc Hi Freq Units ( 2 )...Smith / Victor O/A Sets...DeWalt Power Tools...Craftsman / Snap On Hand Tools... Two Dodge Mobile Rigs

        Comment


        • #5
          I use WD40 in a hand sprayer from a gallon can. #1 it reduces splatter on my parts that have 1,000's of parts and 4,000-5,000 tacks so i can't be going back to clean each part. And #2 it keeps the parts from rusting overnight esp in the humid summertime. I have found nothing that works better or cheaper. Splatter spray rusts my parts esp the water based kind and the solvent based spray has way to many hazzards. I do wear a chemical respirator and weld in my dooorway with a fan blowing out so i don't notice any strange vapor. Now this i just my way that i have been doing it for the last 8 years yours may vary. Just thought i would share...Bob
          Bob Wright

          Spool Gun conversion. How To Do It. Below.
          http://www.millerwelds.com/resources...php?albumid=48

          Comment

          Working...
          X