Announcement

Collapse
No announcement yet.

Spoolmatic 1

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Spoolmatic 1

    Ok guys here's the deal, I just got a new TB302 and 30-A spoolgun with wc-24. My question is can I adapt my old spoolmatic 1 to run off of this setup. From what I can see the only difference is the pins on the plug. Anybody have any thoughts or ideas?

  • #2
    Well, if you were to remoove the circuit board out of the Spoolamtic 1, and stick a 10K 2 watt potentiometer into it.

    Then you could hookup 2 wires for trigger, 2 wires for motor and 3 wires for the potentiometer.

    However gas would be on all the time.

    As it stands the existing wiring , 4 wires are for the 35 VDC input to the gun, a brake and contactor control.

    So as it stands a Spoolmatic 1 gun cannot be used with a WC-24

    Comment


    • #3
      Cruizer, thanks for the info. I got the spoolmatic for free, so nothing lost nothing gained.

      Comment


      • #4
        The WC-1 weld control would be needed to use the SM-1 "as is" with your TB 302 but you already have the more compact and lighter WC-24 and 30A combination.
        MM200 w/spot controller and Spoolmatic 1
        Syncrowave 180 SD
        Bobcat 225G Plus LPG/NG w/14-pin*
        *Homemade Suitcase Wire Feeder
        *HF-251D-1
        *WC-1S & Spoolmatic 1
        PakMaster 100XL
        Marquette "Star Jet" 21-110

        Comment


        • #5
          trust me id much rather run the 30-a but you can never have enough tools! thanks for all the replies

          Comment


          • #6
            Keep in mind the SM-1 was a direct connect spoolgun for the early Millermatic 200s with the 4-pin spoolgun receptacle, do not require the WC-1 and are sought after from time to time.
            MM200 w/spot controller and Spoolmatic 1
            Syncrowave 180 SD
            Bobcat 225G Plus LPG/NG w/14-pin*
            *Homemade Suitcase Wire Feeder
            *HF-251D-1
            *WC-1S & Spoolmatic 1
            PakMaster 100XL
            Marquette "Star Jet" 21-110

            Comment


            • #7
              Duaneb55, its funny you mention that machine. The sppolmatic I have came off that very machine. I got it for a good price. I will sell it if someone has a need for it.

              Comment


              • #8
                I'd say free is a good price.

                I don't need another one but if the price is right or for the benefit of anyone that may, what would you ask for it and would you be willing to package it up and ship it?
                MM200 w/spot controller and Spoolmatic 1
                Syncrowave 180 SD
                Bobcat 225G Plus LPG/NG w/14-pin*
                *Homemade Suitcase Wire Feeder
                *HF-251D-1
                *WC-1S & Spoolmatic 1
                PakMaster 100XL
                Marquette "Star Jet" 21-110

                Comment


                • #9
                  I have had it for 2 years, and never used it. I paid $40 for it. Make me an offer, i have no problem shipping buyer pays the frieght. I am always open to intresting trades too. I would rather see someone get some use fromt it than have it sit in my shop and collect dust.

                  Comment


                  • #10
                    spoolmatic 1

                    Did you sell your spoolmatic 1 yet. I will buy it.
                    Scott in Fremont, CA

                    i'll double your investment


                    Originally posted by Art. View Post
                    I have had it for 2 years, and never used it. I paid $40 for it. Make me an offer, i have no problem shipping buyer pays the frieght. I am always open to intresting trades too. I would rather see someone get some use fromt it than have it sit in my shop and collect dust.

                    Comment


                    • #11
                      Spoolmatic 1

                      I have one that is in great shape. It wasn't used much before being forgotten about up on the mezzanine. PM me your contact info and we can see if we can work something out.
                      Miller XMT 304 w/ 70 series feeder and Optima Pulse Control
                      Miller AEAD 200LE w/ Miller HF-251D
                      Lincoln Idealarc Tig-250/250
                      Lincoln PowerMig 140C w/ Magnum 100SG
                      Century 145 Mig
                      Thermal Dynamics Cutmaster 82

                      Comment


                      • #12
                        vividus, scott i sent you a pm. contact me if your intrested in the spool gun.

                        Comment

                        Working...
                        X