Announcement

Collapse
No announcement yet.

Is it Art or just good workmanship

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Is it Art or just good workmanship

    Here are some photos of a drag race manifold builder. I have not gone through the whole thread. But he talks more about the welds further in the thread.
    http://www.yellowbullet.com/forum/sh...28&postcount=4

    http://www.yellowbullet.com/forum/sh...28#post1282128
    Truly works of art
    glen, If your not on the edge, your wasting space

  • #2
    I would have to agree on the Work of ART reference. Jim
    Welding in Crete
    Syncrowave 350 LX
    Millermatic 252
    Millermatic 180 w Spoolgun
    Miller Gold Seal 155
    Miller Elite welding helmet
    JD2 Tubing bender with Hydraulic conversion
    Evolution Raptor15" SteelDry Cut Saw
    Hypertherm Powermax 30
    Some really cool hammers BIG and small

    Comment


    • #3
      I always thought that good worksmanship is art...

      Frank

      Comment


      • #4
        That guy's work is off the charts. I've seen it posted on quite a few sites. Every site except one was very impressed, that one being a local import forum...."lots of guys can weld like that, it's not that hard with practice." A couple members on there were not impressed with it, and insinuated that if I was, I must not be much a welder. So I asked them for some examples of their or their friend's work, because if a "lot" of people can weld like that, there should be plenty of pics available from guys they know.

        Wouldn't ya know it, nobody came up with anything
        www.facebook.com/browndogwelding

        Blog at TheFabricator.com

        www.browndogwelding.com

        Comment


        • #5
          Beautiful work!! Especially the consistancy in tight places!
          Inspiring to say the least!!

          Tim
          sigpicRetired Elevator Consrtructor Local 19 IUEC
          AK bush pilot (no longer in AK) too old and no longer bold)
          Chaplain CMA chapter 26
          Dynasty200dx (new and loving it)
          MM-252 (NEW AND LEARNING IT)
          Hypertherm PM-45
          Miller 140 mig 110v
          Vtwin builder

          Comment


          • #6
            That is amazing work!
            sigpic
            Millermatic 252
            Miller Dynasty 200DX

            Comment


            • #7
              That should be the centre peice on the dinning room table.

              Comment


              • #8
                **** I can weld like that, I my dreams.
                Gave me some idears.
                Be safe
                Jeff

                Give more than you get and
                you will get more than ya need.
                This is true for the good and bad
                that life puts out.

                Comment


                • #9
                  Wow! That is serious concentration. I wish my al beads always looked that good!
                  Dynasty 200 DX runner
                  Sync 350 LX
                  XMT 300 w/D74 and roughnecks
                  Hobart 135
                  ESAB PowerCut 875 plasma

                  Comment


                  • #10
                    I am one day for any of my beads all the way around a tube to look that good!

                    Mr2man,
                    your signature shows that we have the same machines!! Sharp minds think alike!!!

                    Tim
                    sigpicRetired Elevator Consrtructor Local 19 IUEC
                    AK bush pilot (no longer in AK) too old and no longer bold)
                    Chaplain CMA chapter 26
                    Dynasty200dx (new and loving it)
                    MM-252 (NEW AND LEARNING IT)
                    Hypertherm PM-45
                    Miller 140 mig 110v
                    Vtwin builder

                    Comment


                    • #11
                      Oh my wow! That work is completely out of control...
                      --Andrew
                      Frontline Fabrication

                      Comment


                      • #12
                        Originally posted by Ultrachop View Post
                        Mr2man,
                        your signature shows that we have the same machines!! Sharp minds think alike!!!

                        Tim
                        I noticed the same thing yesterday. We have good taste
                        sigpic
                        Millermatic 252
                        Miller Dynasty 200DX

                        Comment


                        • #13
                          I hope one day that my Tig aluminum welds look that good. ****, I hope any of my welds look that good. Ever.

                          I think the best word for that kind of quality, is: Perfect.
                          Precision is only as important as the project...if you're building a rocket ship...1/64" would matter. If you're building a sledgehammer...an 1/8" probably wont.

                          Comment


                          • #14
                            That's some remarkable workmanship! I couldn't weld aluminum like that in my dreams.
                            Miller Syncrowave 200
                            Homemade Water Cooler
                            130XP MIG
                            Spectrum 375
                            60 year old Logan Lathe
                            Select Machine and Tool Mill
                            More stuff than I can keep track of..

                            Comment

                            Working...
                            X