The weather is finally warm and the son dropped off his drill Sunday so I going to do the welding table job this weekend. I have a question on...

I wasn't suggesting on doing any modifications to the 325. I was just trying to figure out a way to cool it better, more theory if anything. Engine...

I'm wanting to cut a couple of holes in my concrete floor and install some 2" receiver hitch tubes in them to be able to install and remove some...

Getting alot of 325's in. Now these run great in the winter. so so much in the summer. I beleve this is because of the engine getting freaking hot...

Could someone that sandblasts industrial steel for a living tell me what size air supply tank,CFM, PSI and tip size you would use to blast a truck...

Looked at a new Miller catalog the other day. Can't find the Passport Plus anymore, and that was a machine I have pondered getting as being a lot...

So I'm a beginner welder, I went to school and got my certification and learned nearly every process directly related to welding and fabricating ....

Hey there. I have made some welds on 3/16" aluminum. the welds need to be ground down. whats the best wheel to take off the initial weld, then whats...

I'm running a ranger 305g with 1700 hours on it. When welding it is popping and spitting more than normal. Tried different heat and compared head to...

So some of you may remember me asking around for 75 ton hydraulic cylinders for a press brake I planned on building. Found a couple cylinders about 3...

Hi, I just got a new mm180autoset and have no welding exp. I'm going to weld a new radiator core support on a 04 mustang. New support has whats...

Ok so I have my outboard bracket frame together, and I have to weld on the outboard mounting plate. I have a piece of 3/4" aluminum plate and I have...

Hello, I'm new to welding. Actually became my task in work. A little scared with tig aluminum. O&M scared me with warnings. Have stick welded and...

well a few weeks ago i asked yall some questions about building a fireplace, come to find out this was a remodel and the fireplace insert was already...

The first pictures are of a new Extech IR thermometer. I been wanting one for silver brazing. The other pics show how I did the Trubolt job. ...

Anybody else here doing this? I had to move recently, might have to again at some point. Moving is a gigantic hassle, just awful. Oh, you get around...

i am looking for someone to build me a heavy duty easily removable push bumper for my 2006 chevy 1500. i dont want to remove the bottom valance of...

I have to have my cataracts removed, going in the 20 of June to see the doc. Has any welders had theirs removed, was it hard to weld afterwards? ...

Normally out of AZ/UT country but I find myself in northern Vermont with some free time. Any impressive engineering feats or awesome Fab shops to...

I have a 12 RC feeder. The 14 pin connector pig tail is showing wear. Now the wire feeder will start but the machine acts as though the contactor...

Hi all, First off, sorry to post this request here, but there was no provision for work related post and I'm in a pinch so here goes...... I am...

My customer just bought a used 953 Cat loader. Came as an open top with no rops. He wanted something to keep the rain off as well as any errant...

Hi All, I am still a novice tig welder and I am changing out my argon bottle for the first time. It seems like it did not last very long. I do...

What was the last advertise price on Miller passport plus before they became discontinued ?.

Hi guys, I am new to this forum and I am hoping someone can point me in the right direction to get rid of a gremlin I have in our welding shop. I...

Got a 350P with a Python push/pull gun and it seems to have a gas delivery issue. I have to have the flowmeter cranked to max in order to get proper...

Over the years the bush hogs tail wheel's bushings wore out and oblonged the axle holes in the yoke. So I took the yoke and wheel off the cutter,...

Ok so i have welding experience in stick, tig, and mig. I currently have a 110v mig with steel and stainless tanks and spools. I also have a 220v...

Need casters for that special project, design your own it says. http://www.casterconcepts.com/

I must have a 55 ?? I dont know anything about plasmas but doubt the welding supply has all the parts ojn hand.m This was less than ideal, so was...