Miller Introduces Wireless Foot Remote for TIG; Wireless Hand Remote for Stick, TIG, MIG and Flux Cored Welding
 |
Miller’s Wireless Remote Foot Control gives TIG welders a 90-ft. work radius and eliminates tripping hazards and the hassles associated with a remote cord. |
New wireless remote welding controls from Miller improve productivity, eliminate clutter and cord tangles in the work area, eliminate cord failure and associated downtime/repair costs, and extend the operator’s welding range without adding cord extensions
Highlights/Key Facts
- Improves productivity: less time repositioning remote around the work area
- Saves money: eliminates extensions, cord failures, costly maintenance and downtime
- Improves safety through reduced clutter and fewer tripping hazards
- Multiple units work in close proximity with no interference
- Easy to set-up and install
APPLETON, Wis., October 11, 2010—Miller Electric Mfg. Co. introduces the new Wireless Remote Hand and Foot Controls for welding, designed to improve productivity, reduce clutter in the work area, and eliminate expensive cords and extensions that are exposed to industrial wear and tear. Miller’s new wireless products include the first ever Wireless Remote Foot Control for TIG welding, and the Wireless Remote Hand Control for Stick, TIG, MIG and Flux Cored welding.
Miller’s wireless remote controls provide the same responsiveness, performance and effectiveness of corded models and are easy to use. A wireless remote eliminates the potential wear and failure of a remote cord and the associated downtime/cost of replacement. It improves productivity by allowing the welder to quickly reposition the remote around the work area without having to untangle cords. Safety is also improved through reduced clutter and fewer tripping hazards in the work area.
 |
| A digital display and the ability to incrementally change welding parameters at the point of use gives the welder control to adjust settings based on different joint configurations, electrode and wire sizes. |
The Wireless Remote Foot Control, designed specifically for TIG welding in manufacturing, fabrication and plant applications, allows the operator to adjust amperage at the point of use without being limited to the range of the remote cord. The Wireless Remote Hand Control, designed for Stick, TIG, MIG and Flux Cored welding, allows the operator to adjust parameters for different joint configurations, electrodes and wire types/sizes at the point of use instead of walking back to the machine. Designed for construction, fabrication, manufacturing and plant applications, it also allows the operator to increase or decrease machine parameters in increments from one to five percent, and preset the percentage of output of the machine before welding.
Links
Wireless Remote Foot Control Product Page
Wireless Remote Foot Control Spec Sheet
Wireless Remote Hand Control Product Page
Wireless Remote Hand Control Spec Sheet
Miller’s Wireless Remote Customer Video Testimonials
Industry Quotes
“After switching to a wireless remote control we concluded that we were shaving three minutes off the cycle time. If you’re making ten trikes each day, now you are saving 30 minutes—that’s one more trike I can build each day.”
—Paulo Camasmie, owner, Big Cat Human Powered Vehicles
“The Wireless Remote Hand Control’s digital display allows me to have complete control of the molten puddle and know exactly what my settings are. It makes welding much easier for me and my helper”
—Garry Allison, pipeline welder, Local Union 798
“We’ve always kept two spares, but there were times when we’d go through both of them and damage a third within a couple of days. Overall lifespan of a pedal in my shop is four months (because of the damage done to the cord). If we went through three a year, that’s $720 in pedals per machine.”
—Rick Arnold, owner, RAFAB Specialty Fabrication
“Sometimes we have two jobs going at the same time that we need to have access to. Before you had to take the pedal and the wire and move around the piece. Now it’s just a matter of pushing it with your foot and you’re there.”
—Al Reyes, welder and fabricator, Magnus Hi-Tech
Additional News Release Information
Miller’s wireless foot and hand remote controls are quickly and easily paired with any Miller 14-pin wireless receiver and are ready to use right out of the box. The transmitter is powered by three AA batteries and provides the operator with a range of either 90 ft. (foot control) or 300 ft. (hand control). Multiple frequency sharing allows up to 20 systems to operate in a 90-ft. radius without system interference or cross talk and with no delay.About Miller
Miller Electric Mfg. Co., headquartered in Appleton, Wis., is a leading worldwide manufacturer of Miller brand arc welding products and is a wholly owned subsidiary of Illinois Tool Works Inc. (NYSE: ITW).
For more information, visit Miller’s Web site at www.MillerWelds.com, call 1-800-4-A-Miller (800-426-4553), e-mail info@millerwelds.com, fax 877-327-8132, or write to Miller Electric Mfg. Co., P.O. Box 100, Lithonia, GA 30058.
Click to download Miller logos
Click to download Miller desktop images
Editorial Contact: Bill Elverman, Insight Marketing, LLC (262) 240-9790, bille@imipr.com.
